Who all has injected what with slin pins?

[miplank]

For tren and masteron i would backload slin pins for the week (drawing with a 23 gauge of course).

So then you've got your back loaded little slin pin with thick oil in it. Grab a hair dryer, hold it upside down, and "roll" the tube back and forth over the hot air. Do this for about a minute. It still takes about 50 seconds to push a CC through a 29 gauge slinpin but the benefits far outweight the inconvenience.

I've done this with some THICK oil too and it works like a charm. For frequent prop/ace injections, this is THE way to roll.

I'm ok with being called a pussy.

Pussy!

 

[mus1cjunk1e]

I just need to lean up a little then I'm all over this. I already bought some 5/8in 25ga and 1/2in 27ga pins that I want to try out but I have to cut up some more first. All the gear I use now is EO based so it's thin as hell anyway. May still need to heat it up a little to get it through a 27 or 29ga pin... we'll see.

If you're lean enough, I see no reason not to do it.

 

[beach_bum_dude]

Good info as I had no idea heating it made that much of a difference! My pin cushion body thanks you!

 

[Cardinal Slin]

Always get the typical bunch claimin things...

To answer your question dude, I have shot everything with a slin pin with no worries what so ever. Oil and water fit through - it's all to do with pressure and because the barrel of a slin pin is so thin, the pressure exerted is far greater and so oil can go through.

The only time I ever use a 25gauge instead of a slin pin is when I need to inject 2ml + and only wish to poke myself once.

I have no idea on god's earth why people use 21 and 23g pins - I can't figure it out for the life of me.

 

[Olivelawn]

I just need to lean up a little then I'm all over this. I already bought some 5/8in 25ga and 1/2in 27ga pins that I want to try out but I have to cut up some more first. All the gear I use now is EO based so it's thin as hell anyway. May still need to heat it up a little to get it through a 27 or 29ga pin... we'll see.

If you're lean enough, I see no reason not to do it.

Don't preload all of your stuff. EO will rot the rubber stopper in the syringe.

 

[mus1cjunk1e]

Don't preload all of your stuff. EO will rot the rubber stopper in the syringe.

Good advice. In fact I don't like pre-loading in general. I've only done it to pre-load hcg when I bought amps instead of vials.

On that note though, I wonder about the rubber stoppers in the vials.... Maybe they use a special kind that EO doesn't rot?

 

[centy]

I wish. It takes me damn near 5 minutes to force schering primo thru a 25G. Shit's thicker than molasses in January.

 

[RADAR]

I was tempted to try this with my test-e as the stuff I use is very thin. I'm certain it would've worked in a slin pin, but all I had were 1/2" pinz.

Thats what i use, after poking in press down hard to bury the needle deeper,then inj.
No problems what so ever!

RADAR

 

[big___mike]

Always get the typical bunch claimin things...

To answer your question dude, I have shot everything with a slin pin with no worries what so ever. Oil and water fit through - it's all to do with pressure and because the barrel of a slin pin is so thin, the pressure exerted is far greater and so oil can go through.

The only time I ever use a 25gauge instead of a slin pin is when I need to inject 2ml + and only wish to poke myself once.

I have no idea on god's earth why people use 21 and 23g pins - I can't figure it out for the life of me.

I second this one

 

[crazyivan]

this is news to me, dont konw if i'll try it though