Where do you pin?

[Johnny698]

I use a 25g, 1 inch for over 1ml. For site injects I use a 29g, 1/2in pin. This works for 1ml in the pecs and tris. I've even done calves and bi's back in the day but those are more advanced and risky areas. For larger injects I use the glutes and quads, and I warm the oil up a bit. Using a 25g forces me to inject more slowly which also eases the pressure/pain. Also I like to inject before I exercise that bodypart so the oil gets dispersed better by working the muscle. Lastly... short esters usually hurt to some degree, it's just part of the price we pay

Yeah I pinne my glute and it didn't hurt at all will be doing that for the rest of my cycle an will do quads also

 

[bryce2010]

Yea I pin again in the morning before I lift I'm gonna try in my glute

Sent from my PC36100 using EliteFitness

 

[Johnny698]

Yea I pin again in the morning before I lift I'm gonna try in my glute

Sent from my PC36100 using EliteFitness

Yeah you should , still hurts but far more tolerable then shoulders, also pinned my quad to see how it would feel and it's not to bad either

 

[bryce2010]

I did it this morning wasn't bad at all.

Sent from my PC36100 using EliteFitness

 

[ppgfreak]

I pin my legs more than anything. I will switch to my glut some times, but not a lot. If I'm doing prop or tren (eod pin) I will also do my chest and shoulders. I use a 25g 1" for everything except chest, I have 29g 3/4" for that.

But just a heads up, prop always hurts! Lol

Sent from my ADR6350 using EliteFitness

 

[Tux]

Not the prop I make myself! I think alot of UG's just put too much BA in their prop to keep it from crashing. I've made prop at 100mg/ml and that's never painful. Only when I get to 150mg/ml or more of short esters does it start to hurt, and then I can mix in a little EO to allow for less BA. Find a good brand and even prop shouldn't really hurt!

 

[goin on 4T]

Not the prop I make myself! I think alot of UG's just put too much BA in their prop to keep it from crashing. I've made prop at 100mg/ml and that's never painful. Only when I get to 150mg/ml or more of short esters does it start to hurt, and then I can mix in a little EO to allow for less BA. Find a good brand and even prop shouldn't really hurt!

BA doesn't keep it from crashing the BB does. BA is to keep the bacteria that is in there or any new bacteria from growing. BA doesn't cause PIP either its not like lydocaine.
Prop pain has nothing to do with BA or else all short esters would cause PIP, prop pain is from the ester, which once injected into the muscle crystalizes for several reasons.

 

[Tux]

Perhaps not for you, but whenever I added too much BA in my early days, it always caused more pain. Regardless of the concentration of the hormone. Injecting alcohol into the muscles WILL cause pain. The MAIN reason BA is used in injectables is b/c it's such a good solvent. It's much more powerful as a solvent than BB. The main reasons BB is used is to provide a secondary oil-based solvent to try and prevent the hormone from crashing once the water-soluble BA is absorbed by the tissues, and b/c BB also helps to decrease viscosity of the preparation. Why do you think human-grade gear uses ONLY BA and oil? B/c it's both the main solvent and a sterility agent. Sorry bro but BA is most likely the main cause of the pain... then the ester crashing out of solution hurts on top of that.

 

[Johnny698]

My glute hurts today haha didnt hurt to pin never does its the next days always but more tolerable then shoulders definitely

 

[dakid_84]

Anywhere but the ass lol!

Sent from my SPH-D710