Test Prop

[goin on 4T]

hmmm very interesting .03ba .03bb

 

[sony190]

I'm going to have to try that 3/3 ratio sounds interesting

 

[Mh48500]

I'm going to have to try that 3/3 ratio sounds interesting

Dude it works great. I think with homebrewing you really have to try different formulas to get the mix right for yourself. A lot of people use the default numbers in the steroid calculator and those were just too high of BB for me personally. That just seems like a TON of solvent to inject and these hormones will hold at lower levels.

No matter what, part of the fun of homebrewing is playing around. I have lost a few batches here and there but you learn from it. There seem to be a lot less homebrewers than I would have thought, so sometimes the only way is to try it out.

Regardless, you can start low and work up. Hell you can start with zero BB and go to 2%, 3% or whatever until you see it suspend. If you start at 15% or 18% and you react bad to the level of BB then you are diluting and that has not worked out as good for me.

 

[sony190]

I agree I have lost a few batches here and there as well. I also had a bad reaction to 18bb it is a waste in my opinion. I have brewed many batches of Enanthate with 0 bb with success. I believe hormone can hold with low ratio also, I have done it, just not with prop. now brewing Winnie suspension is a challenge. Here some pics for u guys.View attachment 71663View attachment 71673View attachment 71683

 

[Mh48500]

Sweet pics! I have not tried Winny yet, but hopefully soon. Yeah prop holds pretty easily at 100mg, after that it gets tricky. I actually have some that fell pretty bad out of suspension and I did not want to increase the BB and so I set it to the side. Last week I thought what a f"in waste and I shook it up real good and pulled it into the syringe crystals and all. It takes forever to fill 2 or 3 ml but that crap kicks HARD. It can get a bit painful, but hey I like to try things out so I can talk from experience.

I have read that winny is one of the hardest compounds, especially water based so kudos on that brew!

 

[goin on 4T]

Nice work, I wasn't trying to make the least amount of solvent in my gear, just volume of quality that was super consistant.
But when I was doing it for personal than hell yeah. And the powders are so cheap. Esp in Keys

I agree I have lost a few batches here and there as well. I also had a bad reaction to 18bb it is a waste in my opinion. I have brewed many batches of Enanthate with 0 bb with success. I believe hormone can hold with low ratio also, I have done it, just not with prop. now brewing Winnie suspension is a challenge. Here some pics for u guys.View attachment 71663View attachment 71673View attachment 71683

 

[Boo78]

[FONT=&quot]Test Prop for 5 grams

5 grams powder
43.25 ml sesame oil
1.5ml Benzyl AlcoholA 3%
1.5ml Benzyl Benzoate 3%
Syringes
Vial
Sterile Vial
Whatman sterile filter

1. Weigh out 5 grams of powder.
2. Place powder in vial.
3. Add BA & BB to the vial.
4. Heat oil in the oven to help sterilize it, heat to at least 212 degrees F. I usually heat my oil at 275 to be sure, I put the oil in a muffin pan, just fill one of the indentions this is plenty for these experiments. Also heat more oil than you need, as you will not be able to get it all out of the pan.
5. Add oil to the vial, save 2 ml of oil in the syringe for later. Gently shake vial.
6. Heat mixture if necessary. I like heating my powder products, by placing the vial in a frying pan, and placing it on the eye of the stove.
7. Place a 18 or 20 gauge needle in the sterile vial attach whatman sterile filter.
8. Place another needle in the sterile vial to relieve the pressure.
9. Draw out solution with a syringe, run though whatman filter.
10. Take other syringe with 2ml oil, run through whatman into solution.

Makes 50 ml @ 100mg/ml

[/FONT]

Sent from my SCH-R970 using Tapatalk

 

[Rileywilliams22]

Can you use grape seed oil instead of sesame oil?