Pre-Loading SUS

[nygiants]

Is there any issues with preloading syringes (500mg SUS) for a 12 week cycle? 24 Pre-Loaded syringes in total?

 

[dabuffguy]

Is there any issues with preloading syringes (500mg SUS) for a 12 week cycle? 24 Pre-Loaded syringes in total?

I would prefer, myself, to load a syringe as I go to use it. I don't think there is an issue with preloading them though. I'd just as soon keep it in the vial until I need it.

 

[Nelson Montana]

The needles tend to be spikes.

 

[nygiants]

The needles tend to be spikes.

Ok so thats bad?

 

[nygiants]

so whats the overall concensous. Yes or No? If not the entire cycle, how bout 6 at a time? I just need to grab, stick and run. I cant be popping tops, struggle to get the oil out every 3 days....

 

[splperformance]

so whats the overall concensous. Yes or No? If not the entire cycle, how bout 6 at a time? I just need to grab, stick and run. I cant be popping tops, struggle to get the oil out every 3 days....

loading syringes takes about 30 seconds if that...lets say you're shooting 1cc/1ml at a time...put an 18g or 20g needle on the syringe and pull 1cc of air into the syringe...push needle through the rubber stopper on the vial and push the 1cc of air into the vial...turn the vial with needle inside and tip upside down/or at a downward angle and wallah, 1cc of sust. is now loaded into the syringe and this whole process took about 30 seconds...now if they are individual glass ampules, use a short serated (spelling???) knife and file down on the ampule around the white line on the ampule...once the line turns colors meaning it's been filed down, pop goes the top...this process takes about 1 minute to do...so all in all, you're looking at 30 seconds to 1:30 seconds to load a syringe...so no need to preload, but if you do, i suggest changing the needles prior to pinning yourself or you might be a lil upset lol

 

[splperformance]

btw, after you load the syringe, be sure to put a 22 or 23 gauge needle back on the syringe lol

 

[79steeler]

I thought of this and decided against it.

 

[nygiants]

btw, after you load the syringe, be sure to put a 22 or 23 gauge needle back on the syringe lol

OK, how bout this. I preload all my syringes for the enitre cycle with a 20G (easier to suck out of the vial) and leave on the 20G head. When I am about to inject, I change the head to my usual 25G.

 

[GUARDIAN]

i think it is only absolutely necessary for amps where u only need 1/2 ml and need to store the other 1/2 ml for later.

 

[motiondo]

I have pre-loaded an entire cycle. Also I think the very experienced voices here might tell you the same thing. I would as splperformance suggested and get a 18 ga, or 20 ga. put it in the syringe originally and push it into the vial ...draw up the amount you want/need into the syringe, twist off the 18/20 ga needle, leaving it in the vial and replave the original 23/25 ga needle back onto the now prepared syringe. You can pre-loasd your entire cycle this way. Store the preloads in to a ziplock baggie, and store some place cool and hell why not dark too...(like bottom of your drawer) Now you're all set. I doubt you will find any difference in the potency or sterility if you take simple precautions like you should always be doing any time your talking about handling a subsatnce or the mechanisim through which you are going to injest something into your body...just my 2cents.