Post injection lump

[cr0n3k]

Currently in the middle of a test e cycle. My last two shots in the rear has led to a lump in each cheek. Did not happen with my first 3 shots. It's 300mg using 1.5 22 gauge pins. Looks
Ike after a week, the first one is getting smaller and no longer shows a red mark on my butt.

What could be the issue and what can I do to get he lump tomorrow away. Tried heating pad and trying to massage it out.

 

[stevesmi]

if you are angling wrong you could be missing the muscle. the needle you are using is ample size so if that isn't the issue then it could be bad gear

 

[cr0n3k]

if you are angling wrong you could be missing the muscle. the needle you are using is ample size so if that isn't the issue then it could be bad gear

Anyway to know for sure? I did not have these issues with the first few shots. Let's say its bad gear...what can I do? I would not be able to replace the test e for at least 2 weeks. Am I still getting the effects of it even with the lump and all that? I still feel good. I am about to start HCGenerate so not sure what to do if I should not use the test e anymore. Any advice would be greatly appreciated.

 

[Jefferyaron]

Are you tightening up while injecting? I did once it was horrible...

 

[cr0n3k]

Are you tightening up while injecting? I did once it was horrible...

It's possible. Just drives me nuts that first few shots were fine. Last two shots led to lumps. Am I still getting the gear and its effects? Is the lump just a reaction or ?. Anyway to know if its the gear? Should I stop or....?

 

[Jefferyaron]

Tightening up fucked my shit up for a week lol. Also warm the oil up before injecting helps me out quite a bit.

 

[cr0n3k]

Tightening up fucked my shit up for a week lol. Also warm the oil up before injecting helps me out quite a bit.

Warm it up how?

 

[semper03]

Warm it up how?

Run the vial under warm water or use a blow dryer, just don't get it too hot.

 

[Sherk]

I use a blow dryer after I draw it into the syringe. Easiest and fastest but be carful not to heat it up too much.

 

[Jefferyaron]

^^ this

 

[dylangemelli]

have you tried injecting in quads or delts?

 

[cr0n3k]

I use a blow dryer after I draw it into the syringe. Easiest and fastest but be carful not to heat it up too much.

About how long do you blow dry it? You guys think this would help with to prevent lump?

 

[semper03]

About how long do you blow dry it? You guys think this would help with to prevent lump?

It's not rocket science bro, just a few seconds.

 

[Sherk]

You can feel it when it's warm. It doesn't take very long because there's not much liquid to even 3ml. It heats up pretty quick. If you wanted a number then idk, 10-20 sec maybe. I don't really count. Some blow dryers have a higher output than others too

 

[RADAR]

Lots of good info here, i also use a blow dryer on certaing brands you will know how hot it gets by touching the syringe it should be warm to the touch then shake it abit to even out the heat before injecting, Dylan has also posted good advice Delts are the least painful, i do 95% of all my injects in the delt area.

 

[Sherk]

Pecs injected with a slin pin is painless too. Never once got even slight pip when using a slin.

 

[cr0n3k]

have you tried injecting in quads or delts?

never tried it...what pins are recommended for delts? Also, what can I do about the lump? Heating pad or just leave it and it should go away on its own?

 

[Jefferyaron]

It'll go away on it's own but a heating pad should speed up the process

 

[rangersleadtheway]

It's not rocket science bro, just a few seconds.

Hahahaha! love your frustration.

 

[robph]

hey bro,it seems to me you need to switch injection sites. if you are always using your butt cheeks its tine to start pining your shoulders and triceps both are easy to do it, do left shoulder, then right shoulderl then left tri, then right tri then repeat give your cheeks a little break your bumps should go away by then, if it becomes infected and you start to get fevers goto the doc asap.