23 gauge needles

[cunctator]

In some of the injection-related threads, some people 'boasted' that they were pu**ies so they used 23 gauge needles to inject. The only stuff I have ever injected has been from (Note: NOT a source!!!----does not matter no UG names) whose oils are notoriously thick, and there is no way you could eject even a drop of this stuff using a 23. In fact, it's very difficult to do so even using a 21 gauge needle.

Are other manufacturers' oils so much less thick than or were the Bro's just full of Shit? Can you actually inject oil-based stuff with a 23?

 

[misticat]

sure can... i inject everything through 23g.. unless its winny(water not oil) then i use 25g.

i use a 18g to pull it out of the vial if you use a 23g it takes forever and i get a lot of little bubbles cause i am impatient and pull the plunger all the way back and air gets sucked in behind the rubber piece on the plunger..

 

[ALIN]

In some of the injection-related threads, some people 'boasted' that they were pu**ies so they used 23 gauge needles to inject. The only stuff I have ever injected has been from Note: NOT a source!!!) whose oils are notoriously thick, and there is no way you could eject even a drop of this stuff using a 23. In fact, it's very difficult to do so even using a 21 gauge needle.

Are other manufacturers' oils so much less thick than were the Bro's just full of Shit? Can you actually inject oil-based stuff with a 23?

no lie,,,i use 23 and 25 constantly.

 

[cuts82]

try a 18g in the ass and see if people are bullshiting about using 23's!
try heating the stuff up before hand man

 

[lilj888]

23 is what i use nice and very painless

 

[needtogetaas]

up I use onl 23 1.5 on all injects.

 

[lookinfit75]

22-25. All depends on what I can get my hands on.

 

[layinback]

i use a 21 to pull and a 23 to inject. everybody i know uses 23.

 

[wolfman87]

25 is the only one i've ever used. but i'm tired of it taking forever so next time i'm gonna use 23.

 

[nzrodney]

23g or 25g is standard issue

 

[NEO1]

18 2 draw, 21 to inject (yes I know, I know)

 

[perryscoon]

no lie,,,i use 23 and 25 constantly.

me too

 

[Christianlifter]

try a 18g in the ass and see if people are bullshiting about using 23's!
try heating the stuff up before hand man

Quote of the year right there!
I just got off the floor........

 

[Ron_Mexico]

I pull with 22's

inject with 23's in glutes and thigh

inject with 25's on shoulder and tri's

 

[the_alcatraz]

pull with 18 and inject with 23.

btw, as a dare, I've injected with 18 and 14 before.

 

[Christianlifter]

yea I used to do that. Until I got my pins mixed up and stabbed myself with a severly infected 18. I used it more than once and cleaned it with alcohol every time (low on pins at the time). Ended up needing 2 surgeries with a hole the size of an apple that had to be cleaned daily with what felt like a pipe cleaner and had to heal from the inside out. Still cant inject on my left glute 3 years later. So be careful.

 

[christian40]

I use a 25. it takes a while to get it in me through such a small pin. I have to draw with a larger gauge though.

 

[coreyv93]

18 to draw, 23 to inject oil.
now test suspension is different, try 18 to draw and 22 to inject, or maybe it was 21 g? i dont remember, but it was a straw