Please Scroll Down to See Forums Below Stacemranger
New member
The test prop I'm using hurts like hell, I need to know how to bake it to reduce the BA. Someone help me out. I searched but couldn't find anything.
Test prop hurts like hell, someone give me some info on baking
- Thread starter Stacemranger
- Start date
Stacemranger said:
Another option would be to cut it with some sterile grapseed oil. Or B-12.
It will hurt a lot less.
Stacemranger
New member
halfcenturian said:
I would like more info on this. grapeseed oil? or grapseed oil? Where can I get this? Do I do like 1cc of test and 1 cc of oil or what?
off_safety
New member
put in ur oven on 250 for 15 minutes with just the needle in the top. this should work for ya. i also soak my prop in warm water before i inject. it helps a lot. good luck.
BENCHSHIRT51
New member
run some eq or primo to cut it, i have the same prob w test400 and i cut it w eq and it's all goodStacemranger said:
Stacemranger
New member
I'm gonna be using EQ with it in 4 weeks but not now. I'm gonna try what off safety said and bake it. I know about cutting the oils, I cut test e with deca and it was smooth.
Stacemranger
New member
Gonna be 16 weeks with the EQ. Don't know if 20 will be too long.
Stacemranger
New member
I baked a couple vials last night and gave myself an inject and this morning doesn't seem to sore. We'll find out.
Try using a product that uses EO for their prop instead...there are a few labs out there. I'm currently SL which is 200 mg/ml and its completely pain free. The last prop I used left me crippled for days after injection..and w/ eod injections...I was seriously considering investing in a wheelchair, so believe me I feel your pain
stressman13
New member
baking always helps me. runing the vial under water before injection works too. (both already mentioned) EO based Prop is the best solution to this.
Stacemranger
New member
Alright guys, I baked the vials with an 18g needle in the top. The pan I had them in had a small bit of oil in the bottom and one of the vials was wet. It didn't even look like it lost any to me(they were all new). I gave myself a shot in the glutes and it felt just like a normal shot today, no crippling pain like in my quad the other day.
Stacemranger
New member
DJ_UFO said:
No, it was seriously bad. I've done a 14 week cycle and a 20 week cycle before this and never had pain like that. I had trouble walking on flat ground and where we live there are two sets of stairs which were hell to go up.
Stacemranger
New member
52_21_30 said:
Still no pain from the glute shot after baking. Seems to have worked.
solidspine
New member
I have had great success baking test at 220 degrees for 30 minutes, vented of course with an 18 gauge needle.
In the oven 220 degrees brings it close to boiling, but it never actually boils, and 30 minutes is long enough. When we autoclave in the OR it is at pressurized 275 degrees for 12 minutes.
I baked gear once for 35-45 minutes, the plastic tip of the proximal end of the needle melted, not harm, just melted. So keep to 30 minutes.
Oh, and I don’t think baking prop will help, the ester is just made by Satan.
Let us know.
In the oven 220 degrees brings it close to boiling, but it never actually boils, and 30 minutes is long enough. When we autoclave in the OR it is at pressurized 275 degrees for 12 minutes.
I baked gear once for 35-45 minutes, the plastic tip of the proximal end of the needle melted, not harm, just melted. So keep to 30 minutes.
Oh, and I don’t think baking prop will help, the ester is just made by Satan.
Let us know.
taste-icles
New member
Where are you injecting? when i shoot low on the thigh i get pain, but mid or high on my thigh, no problems, i shoot too low and it is EXACTLY like getting whacked with an aluminum Lacrosse shaft!
Stacemranger
New member
That may have been the problem as well, i did do it kinda low. I'll go higher next time as well.
Castro_bigdog
New member
I wish the Test 400 I messed with some years ago was cooked like that, I would of not limped around for 10 weeks LOL.... 
I wrote a similiar thread bout this few days ago on prop,tren,mast blend. (like the vets say) bake for 30min at 250 and the pain was 1/6 of what it usually was. It's tips like that, that you could never get from any steroid info sites or books. Best EF advice i've ever got.
Just started a prop cycle and will do my second shot tonight. I got some baad pain in my glute and I been thinking about doing tonights shot in the same glute, or else I wont be able to move much :S
Can someone please try to explain this baking procedure more detailed, I got 10ml vials of 100mg prop / ml.
Ohh, and 21G is the bigest needles I got.
Please help, cant stand the pain almost, hehe.
Can someone please try to explain this baking procedure more detailed, I got 10ml vials of 100mg prop / ml.
Ohh, and 21G is the bigest needles I got.
Please help, cant stand the pain almost, hehe.
Castro_bigdog
New member
jasonxxx said:
Welcome to the world of prop and it pain..........
hehe, I think I got this baking all wrong, I thought I could just put my vials in the oven and heat them 30 mins and then everything would be fine, Im totally wrong I guess, no? 
But I really need to make the pain less somehow, will try to inject my 1,5cc much slower 2-3 mins?
Also heat the syringe under warm water for 30 secs before injection.
Good choices?
But I really need to make the pain less somehow, will try to inject my 1,5cc much slower 2-3 mins?
Also heat the syringe under warm water for 30 secs before injection.
Good choices?
