Please Scroll Down to See Forums Below
napsgear
genezapharmateuticals
domestic-supply
puritysourcelabs
UGL OZ
UGFREAK
napsgeargenezapharmateuticals domestic-supplypuritysourcelabsUGL OZUGFREAK

Scar Tissue!!

I use 25g 1.5in pinz....have 4 cycles under my belt and my quads are filling up with scar tissue...I find that if i inject in my glutes...i develop less scar tissue for some reason..but I hate doing glute injects....id rather do quads and calfs anyday of the week .... No more ED or EOD cycles for me....I learned that lesson the hard way...just cant do it...

My question is...is there anything that you can add to your gear to thin it out? I wouldnt have aproblem doing more injects with say a 29g pin if there was something safe to thin out the gear with..that wont make it BURN like a bitch
 
BIGDHO said:
I had the same problem. Try switching to a 21 gauge 1 1/2 needle a put it all the way in the oil will go through faster and being that deep you will pass through the scaring.

Good point, you can go with a longer or shorter needle and miss the scar tissue. I sometimes dont inject as deep as usual and avoid hitting the scar tissues.
 
CENTURION44 said:
I use 25g 1.5in pinz....have 4 cycles under my belt and my quads are filling up with scar tissue...I find that if i inject in my glutes...i develop less scar tissue for some reason..but I hate doing glute injects....id rather do quads and calfs anyday of the week .... No more ED or EOD cycles for me....I learned that lesson the hard way...just cant do it...

My question is...is there anything that you can add to your gear to thin it out? I wouldnt have aproblem doing more injects with say a 29g pin if there was something safe to thin out the gear with..that wont make it BURN like a bitch

I have a whole bunch of 25x1.5 pins you can have. Those are impossible to push. I tried twice and said screw it. I use 1" or 5/8". I was pushing so hard with one of those the body of the syringe ruptured! Started pissing right out of the side of the syringe! You must have some serious patience!
 
Last edited:
I stick with long esters so I don't have to drill too many holes. I also use the smallest needle practicable. I gave up on trying to push oil thru 25g one handed; I save those for b-12. I only use 23gb in the butt/quads for oils and abs/delts for b-12, igf-1, hcg with a 25g or 29g insulin pin.
 
nsashbl01 said:
I have a whole bunch of 25x1.5 pins you can have. Those are impossible to push. I tried twice and said screw it. I use 1" or 5/8". I was pushing so hard with one of those the body of the syringe ruptured! Started pissing right out of the side of the syringe! You must have some serious patience!

I counted with a stop watch.....3cc in my right quad....went thru at 25g 1.5" in just over 30seconds....I warm it up though..and never have had a problem pushing
 
Have you tried ultrasound or interferential electrotherapy to break up the "scar tissue". Might work, just an idea. It is used sometimes to loosen tissue post trauma. It will increase circulation for sure.
 
2NDOMEGA said:
Have you tried ultrasound or interferential electrotherapy to break up the "scar tissue". Might work, just an idea. It is used sometimes to loosen tissue post trauma. It will increase circulation for sure.
I've heard of this, but Im not trying to dish out a truckload of cash to do ultrasounds and shit.
 
CENTURION44 said:
I counted with a stop watch.....3cc in my right quad....went thru at 25g 1.5" in just over 30seconds....I warm it up though..and never have had a problem pushing
What's your method for warming up the gear?
 
Outtlaw said:
What's your method for warming up the gear?


Ultrsounds are not to expensive. Go to a chiro. I run a trickle of hot water. Hold the syringe in it by the needle. let the stream hit the middle of the body and run down towards the plunger.
 
Outtlaw said:
What's your method for warming up the gear?

I use a 20g to draw and 25g to inject...after i draw i lay the full syringe atop a lamp...with a 75 to 100 watt bulb in for about 30 seconds to a minute....just see how it feels...it should be pretty warm to the touch...thins it out ALLOT..Patience is the key..a firm steady push will get it out in no time....id rather spend a minute injecting than be riddled with scar tissue..dont get me wrong..i still get some...but not nearly as much as when i used 22 or 23g pins...
 
Top Bottom