Prop Pain cut with Ethyl Oleate....can I add GSO?

[prochembro]

I got some prop 100mg/ml that's cut with Ethyl Oleate.

It's my first cycle, so as expected the PIP on my virgin muscle (glute so far) is pretty bad.

I can't touch the injection site not sit directly on it. I can walk fine though, and I got no pain either so I don't think my PIP is that bad.

However, I can't see myself being in this pain for 8 more weeks. I was wondering if I can add some sterile GSO to the Prop to ease the pain?

Will that work? And how much should I add?

 

[prochembro]

come on, help a guy with PIP out ppl.

 

[MaxxReps]

I'm not sure but think its the prop thats causing the PIP, not the concentration. But rather than rely on broscience why not try. If you have a vial of strerile GSO draw your shot of test from its vial, then draw the same amount of sterile GSO into the same syringe, mix it up and give it a shot. See what happens.

And if you do, report back and let us know

 

[superturkey]

Some guys add too much BA, that can defiantly hurt.

I'd give it a quick heat up, with an 18g in the top, burn off some of that BA. Even just 15min in pre-boiled water does the trick.


Sent from my iPad using Tapatalk

 

[MaxxReps]

Hey superturkey,

BA doesn't cause debilitating PIP - I've pretty much proven that on myself. Also, putting the vial in pre-boiled water won't get rid of BA. BA has a high boiling point. I think its the hormone itself. Diluting it may or may not help. I'd certainly be interested to hear if it does.

 

[superturkey]

Hey superturkey,
BA doesn't cause debilitating PIP - I've pretty much proven that on myself. Also, putting the vial in pre-boiled water won't get rid of BA. BA has a high boiling point. I think its the hormone itself. Diluting it may or may not help. I'd certainly be interested to hear if it does.

I'm not saying it isn't the compound because as we all know many people complain of PiP from prop.

From experience this technique worked for me.

I had Test 400 and Tren E 200 which rendered my leg useless. A simple heat up with a pin for 20 mins and no more pain.
Explain what else could be happening with this procedure?

Correct ,BA boils around 200 degrees C but does not mean it doesn't evaporate at 100 degrees C.

That is the whole idea of this procedure, you don't want to boil it or it would all go, you still need at least 2% BA.
Heating simply evaporates 'some of the excess'.

I have done this with two cycles worth of gear and had no sterility issues and completely solved my problem with PIP.


Sent from my iPad using Tapatalk

 

[Alphacore200]

It's either the EO or the prop ester. I have used a source in the past that had a disclaimer on their site that stated product contains EO do not use if you are allergic. I shot some "green" colored gear that had EO in it and my shoulder swelled up sucked but went away

 

[WolfpackAlpha]

I found a lot of EO claims are overplayed, EO pain is just as bad as regular mixes, as most guys are mixing in a ton of BA to compensate for EO instability.

 

[Analyst22]

From personal exp Prop shots generally tend to hurt a lot more, How much did u shoot? Mabey you nicked a blood vessel...No pain no gain hey, If the pain is too intense for you then consider a longer acting ester such as cyp or enanthate. Those dont seem to hurt at all if injected properly and you would only need to inj twice a week instead of EOD

 

[EZ_E]

Draw the oil, warm the pin under a blow dryer for a few minutes. Problem solved.