Please Scroll Down to See Forums Below
need help with fina
- Thread starter bulletbob
- Start date
The Almighty
New member
Same thing happened to me. Just heat it on a low heat for about 5-10 minutes and wait for it to dissolve.
R
rocketrman
Guest
it's kool
it's kool. that's what is supposed to happen. do as almighty said. however before you do that, if you had a rod ( glass rod preferably ) crush the pellets in the vial let sit, then heat and gently swirl. from here you can pre-filter ( not necessary though ) then pour vial 1 to vial 2 being carful not to get too much of the "junk" into the #2. let sit to room temp,then sterile filter and you are done.
it's kool. that's what is supposed to happen. do as almighty said. however before you do that, if you had a rod ( glass rod preferably ) crush the pellets in the vial let sit, then heat and gently swirl. from here you can pre-filter ( not necessary though ) then pour vial 1 to vial 2 being carful not to get too much of the "junk" into the #2. let sit to room temp,then sterile filter and you are done.
B
basskiller
Guest
whats left of the binders
R
rocketrman
Guest
the gunk
that stuff bullet is the so called " glue and binders " that hold the tren in the pellets. the magic solution breaks this " bond " and lets the tren become suspended in the solution. then when you add the oil you will see another layer filter out. this what you want to see. 2 layers 1 is kinda reddish brown & the other is off whiteish.
the good stuff is again suspended in the top layer of oil.
yes, heat on the lowest heat setting. or just boil some water. turn off the burner place the vial in the water and gently swirl. you should be able to hold the vial while swirling. if you cant the water is still too hot. this step will help to dissolve any of the remaining pellets.
oh yea, i think the ingredients in the pellets are yellow dye #5 and methlcellouse & ..... shit, something else.
that stuff bullet is the so called " glue and binders " that hold the tren in the pellets. the magic solution breaks this " bond " and lets the tren become suspended in the solution. then when you add the oil you will see another layer filter out. this what you want to see. 2 layers 1 is kinda reddish brown & the other is off whiteish.
the good stuff is again suspended in the top layer of oil.
yes, heat on the lowest heat setting. or just boil some water. turn off the burner place the vial in the water and gently swirl. you should be able to hold the vial while swirling. if you cant the water is still too hot. this step will help to dissolve any of the remaining pellets.
oh yea, i think the ingredients in the pellets are yellow dye #5 and methlcellouse & ..... shit, something else.
Last edited:
R
rocketrman
Guest
bullet you could do that. that is use a coffee filter. if you do, start w/ pouring only the mostly nice clear solution. let it filter. then, you can use another filter or the same one would be fine too. carefully pour the rest of the solution into the filter. try like hell to keep the junk in the vial while you pour. let it filter too. while this is filtering it might start to make your pre-filtered solution a little cloudy. but this is ok. if it does bother you stop the filtering. the amt is minimal anyway. once this is done sterile filter & you will be done.
if you choose not to coffee filter, that is ok too. the was designed so you don't have too. yes leave the junk @ the bottom and try to get as much of the " suspension" as possible. don't strain yourself over a few ml's though.
if you choose not to coffee filter, that is ok too. the was designed so you don't have too. yes leave the junk @ the bottom and try to get as much of the " suspension" as possible. don't strain yourself over a few ml's though.
