Little rubber floaties in juice.....

[Diesel3d]

I get small pices of the the rubber top of the vial in my juice from my drawing needle sometimes...

I spend a lot if time making sure i don't suck them up and inject them..... anyone ever inject a small one by mistake?

 

[boss]

i have never heard of any rubber stopers breaking up in the vial???????? what did you have?

 

[Diesel3d]

sometimes my needle will break it and i'll get a little pice of it in my juice. i know im not the only one!

 

[Code]

Chances are they won't fit into the needle.
But if you want to be 100% safe, get a syringe filter.

 

[Diesel3d]

Im using fina. maybe this only happens to generic steril vials that come from the kits and stuff?

 

[h-train]

happens when i use testerona im just careful so i dont suck it into the pin

 

[waterboy]

get a syringe filter.

What the hell is that

 

[waterboy]

I never had trouble with the rubber but I do some times worry about little bits of glass

 

[genarr3]

I've heard of this happening. I have to believe that the rubber is made from a material that wouldn't harm you if injected, the manufacturer has to have anticipated this happening.

 

[rippedtrojan]

would the body eventually break down and absorb the rubber if that were to happen?

 

[waterboy]

I've heard of this happening. I have to believe that the rubber is made from a material that wouldn't harm you if injected

thats good to know ..

 

[Code]

A syringe filter is a little filter that rests between the syringe and the needle.

Very handy indeed.

BD sells them.

 

[Diesel3d]

the thing is with using a filter just for injecting you might not even get any of the juice out. I wanted to filter some juice i had... i pumped 3 cc's into the filter and it absorbed it all.
In the end i had lost a few ccs even after i tried purging it with air. Those things are amazing.

 

[solidspine]

Don't use the same needle to draw, each time, and don't worry about injecting rubber in your body, just be careful.

You could finish that vial drawing with a smaller needle to minimize sucking up the rubber,

you maybe received old vials and the stoppers dried out.

 

[Diesel3d]

Don't use the same needle to draw, each time, and don't worry about injecting rubber in your body, just be careful.

You could finish that vial drawing with a smaller needle to minimize sucking up the rubber,

you maybe received old vials and the stoppers dried out.

hmm well before i put on a new drawing needle and draw i wipe the top of the vial with alcohol to kill any germs that may have gotten on it from being in my pocket on the way to the bathroom or from where i store it.

That must be it. It must be drying out the rubber. dried + 20g drawing needle must be the problem..

Thanks

 

[gwl9dta4]

sometimes my needle will break it and i'll get a little pice of it in my juice. i know im not the only one!

No you are not. I had that happen with the Greek extraboline, (deca). So i was really carefull not to suck them up into the syringe.

 

[Testosterone Spike]

YESSS!!!!!!!!

I did this once.
I drew a few ccs of deca and an omna cc into my 25gauge.
Then I gave it to my friend to stick for me (this was during the time when I was too chicken to stab myself, hehe). So my friend stabs me, and then about 1/4 went in and then all of a sudden it became increasingly difficult to push the rest through the pin...
Next thing I knew it was like 5 minutes later and my friends hand was turning blue. To make a long story short, the way I found out some of the rubber stopper had gotten into the pin was when I cleaned it with alcohol after. I poured some alcohol into it and tried pushing that out.. when the alcohol wouldnt even squirt through I pushed real hard over the trash can and then the tiny rubber particle shot out like a fucking bullet!
Good thing that shit didnt end up shooting into my ass cheek at lighting speed. God knows what would have happened..

DOCV

 

[_GEEZER_]

Solidspine hit it right on the head.
Use a new pin everytime you draw or inject. Besides, even drawing will dull your needle a little. Minimize your scar tissue too by changing to a new one, especially if you're using big pins (20-23 ga.)

Some people spend HUNDREDS of dollars on a cycle, but when it comes down to it, are hesitant to spend a couple of dollars on shooting it the safe, correct way. Be smart. Not trying to flame anybody, just something to think about.