Help cant load syringes

[biggernu]

Ok i i cant get they syringes to load, i am using 23g 1 1/2 syringes, put 2ccs of air in it, put it in the vial push the air in the vial, but i cant get it to load the syringe i the plunger sucks right down to zero. The cap keeps poping of the vial, i tired another vial and the same thing happens, i cant get the test out of the vial.

 

[GUARDIAN]

i dont draw any air b4 putting into the vial. stick right into the vial after swabbing the top with alcohol. turn vial and syringe upside down. pull back on plunger (i like to pull back 1ml more than I am drawing) and just wait. sometimes 23g takes a little bit to get started and it sure is slow in general.

 

[hesnobradpitt]

Ok i i cant get they syringes to load, i am using 23g 1 1/2 syringes, put 2ccs of air in it, put it in the vial push the air in the vial, but i cant get it to load the syringe i the plunger sucks right down to zero. The cap keeps poping of the vial, i tired another vial and the same thing happens, i cant get the test out of the vial.

Sounds like its vac sealed if the plunger sucks down , just screw of the needle from pin and leave the pin in to see if it draws air to level out then reattach and draw .

Brad.

 

[spankymach1]

buy some 18g and use for drawing and then swap out to the 23g for pins

 

[mus1cjunk1e]

First of all never use the same pin to draw as you do to shoot because sticking it into the vial dulls it and it will hurt like a bitch to shoot. I also use an 18g to draw and a 23g to shoot. If you have to use a 23g, the trick is to pull very slow and steady. Just keep a small amount of constant pulling force on the plunger and you will see it slowly start to fill. But definitely order some 18g pins and use them to pull from the vial (if you want to keep waste down you can just buy one 18g pin and keep in in a small pill bottle that you have cleaned by pouring alcohol in and swishing it around, I've been doing it like that for a while with no problems, just make sure to clean out that pill bottle with alcohol every few weeks)

 

[safety4lyfe]

Yup +1 for musicjunkie...thats what i was going to say.

Pinz are dirt cheap, so why use the same to draw and inject?

Draw 18g - Inject 23g (maybe even 25)

 

[eastcoastplayer]

Am I the only Jackass that doesn't switch pins?

 

[mus1cjunk1e]

Am I the only Jackass that doesn't switch pins?

Yep

 

[eastcoastplayer]

Yep

I had to ask....

 

[centy]

Yep

haha

 

[bluejay]

Am I the only Jackass that doesn't switch pins?

Haha... nah you are not alone...

I don't switch either.

 

[theperfectdrug187]

I'm trying to quit, so I poke with the same syringe to make it hurt... it's not working, my ass is just twice as sore

 

[TexasTurkey1001]

Ok i i cant get they syringes to load, i am using 23g 1 1/2 syringes, put 2ccs of air in it, put it in the vial push the air in the vial, but i cant get it to load the syringe i the plunger sucks right down to zero. The cap keeps poping of the vial, i tired another vial and the same thing happens, i cant get the test out of the vial.

I pull the siringe out to the 2ml mark, insert into vial, push the air in, turn the vial upside down, then slowly pull plunger out to about the 2 1/2 mark then wait. Make sure the needle is screwed tight to the siringe otherwise air will go in and nothing will come out.

I've always used a single 23 guage needle to pull and shoot with... it works fine.

Guess I should try the two needle method of shooting... never seen a doctors office use two needles so why should I ... but wouldn't 'hurt' to try.










-

 

[GUARDIAN]

Haha... nah you are not alone...

I don't switch either.

Lost all respect for ya bro....jk

 

[mus1cjunk1e]

I'm so gangsta I just slice a cut in my quad with a knife and pour it in

 

[perryscoon]

Haha... nah you are not alone...

I don't switch either.

I don't switch either. Not worth the trouble IMHO.

 

[navigatorrs]

Switching the needle takes seconds to do. I love a clean smooth shot!!!!!! Nothing like like it and very sterile also!!! Right from the package to the body is the best way to go way!!

 

[mus1cjunk1e]

Ya I tried once to not switch the needle to see what would happen. I used the same amount of force I usually use, and instead of sliding right in painlessly like usual, it bounced off my skin and just cut me a little lol. That was the last time I tried that.

 

[biggernu]

Ok i got her, i ordered 23g x 1inch, i didn't think to check what i got, but i ended up with 25g 1.5. Ya 25g takes FOREVER to LEAD AND UNLOAD. Had no problems, other then both delts hurt like a mofo, no lumps or red dots, they just hurt and are hard to move my arms. PLaced a rush order for 18g pins and 23g x 1in and 1.5 inch pins.

 

[halfcenturian]

Am I the only Jackass that doesn't switch pins?

NO! I use a 25g to draw and shoot. How can a 23-25g needle hurt? PUSSIES!

 

[GUARDIAN]

NO! I use a 25g to draw and shoot. How can a 23-25g needle hurt? PUSSIES!

the issue wasnt the pain it was sterility.

 

[702daswoll1]

Am I the only Jackass that doesn't switch pins?

Im a no-pin-switching-jack-ass too. No biggie I like dull needles.

 

[hassinba]

Be careful if you're drawing out of your vial with an 18g pin....you can destroy the rubber seal and it can fall into your gear

 

[bubba-d]

buy some 18g and use for drawing and then swap out to the 23g for pins

Thats the way to go!

 

[ViperHMS]

Be careful if you're drawing out of your vial with an 18g pin....you can destroy the rubber seal and it can fall into your gear

Yeah but it wont matter anyway cause it wont make its way through a 23 or 25g pin anyway.

 

[jumpshot]

22 1.5 and I don't switch either. No big deal.

 

[big.nad]

because pins are so cheap there should be no reason to keep and maintain a drawing needle. i get my pins free so ive no need for that.

fresh pin everytime to draw and another fresh pin for every inject.