Fina Rookie Needs help

[Grainger]

I got the Fina (TH) and used a kit to make Tren. I filtered it twice through a .45 um filter just to make sure it was clean. I did not heat it though becuase the vials that I got are a screw cap (From finakit.com) I don't like these but it is not as clean as a vial with rubber gasket etc. It was eaiser to work with however.

In any case I did not want to heat it becuase I wasn't sure about the type of vials that I got (with the screw cap) I did take a shot however and had zero pain. However, I have a red welt on my ass and it does concern me. I am wondering if heating is required. I hate to cook the shit with no cap on.

Has anyone used their kits? What did you do as far as heating? Does the welt suggest that it was not clean? Any help or suggestions would be greatly appreciated.

thanks,
-g

 

[Gcis40]

Sup bud nah man you have nothing to worry about I got the same kits and everything the only thing i did differently was that I crushed my pellets, I didn't heat anything the only thing that heating does is speed up the process and it's find I also get a little red dot here and there...The reason for that is obvious...When you get regular steriods that are made, they are 100% sterile when you make them they are about 95-99% sterile so the red do is just you skin reacting to the part that is not sterile like a cut...It's fine i am on my 6th weak of fina and i love it......

 

[Grainger]

cool....thanks for taking the time to reply.....the other thing I don't like about this stuff is that it is hard to tell the concentration. I used a 4g kit and had a total volume of 26 mls. You have to take into consideration the amount of oil, the volume displacement of the pellets, the "magic" liquid and then make some sort of guesstimate about how much you lost during filtration. Far from an exact science.

All I know is that I got some pretty strong shit. Maybe that had something to do with the welt on my ass.

When I was talking about heating, I wasn't talking about heating in an attempt to disolve the Fina, I was talking about baking at 250 etc.

Anyone else with any thoughts?

 

[Pineapple Devil]

you used a 4g kit and only came out with 26ml?

 

[Gear101]

This is for 1..cartridge of finaplix-h and 1... 2gm kit
With a 2% loss of product in the conversion
If you do everything correctly the Oil(mls) to mg strenth would be as follows.


10ml = 194mg/ml
11ml = 176mg/ml
12ml = 161mg/ml
13ml = 149mg/ml
14ml = 138mg/ml
15ml = 129mg/ml
16ml = 121mg/ml
17ml = 114mg/ml
18ml = 107mg/ml
19ml = 102mg/ml
20ml = 97mg/ml
21ml = 92mg/ml
22ml = 88mg/ml
23ml = 84mg/ml
24ml = 80mg/ml
25ml = 77mg/ml



A word of caution. Some kits have 5mls of magic solution (this is the main factor of pain) and some only have 3mls.
So most people that have tried to convert a higher mg product just take out the oil.


This raises the ratio of "solution to oil" mixture....Which causes the more painful injections.
A better way to raise it would be to add more pellets to a 2gm kit
I"ll do an experiment to see how much can be converted in 3mls on "magic solution"..
and report on it with numbers.

So unless you know and understand the ins and outs of this,
Just stick with converting with all the product(finaplix pellets), oil and magic solution.
*************************************************
This is for 2..cartridges of finaplix-h and 1... 4gm kit
With a 3% loss of product in the conversion
If you do everything correctly the
Oil(mls) to mg strenth would be as follows.

35ml = 110mg/ml
36ml = 108mg/ml
37ml = 104mg/ml
38ml = 102mg/ml
39ml = 99mg/ml
40ml = 97mg/ml
41ml = 95mg/ml
42ml = 92mg/ml
43ml = 90mg/ml
44ml = 88mg/ml
45ml = 86mg/ml
46ml = 84mg/ml
47ml = 82mg/ml
48ml = 80mg/ml
49ml = 79mg/ml
50ml = 77mg/ml

basskiller