Bac/Jin/Terumo 29g mixing question?

[gunrunner]

Hey Guys,
Got a question on mixing Jintropin with bac. water and reading Terumo 29g (1cc) slin pins?
I've got:
Terumo 29g 1/2" (1cc) slin pin.
10iu vials of Jintropin
and 30ml of Bac. Water

I would like to use 2iu ed to start. How much bac. water should I mix with my 10iu of gh? And what is an international unit in relation to a cc?

Thanks guys, this is a first with gh. I will be running a 12weeker of Test cyp and 2iu ed of Jin's. Did a x-ray body comp. test as well as a blood test last month. Will post results/pics when cycle is finished.

Thanks in advance.

 

[buffalo]

I'm tired but i believe this is correct. Use 1ml of bac water with your 10iu bottle of gh,on the slin pin each 10th will be 1 iu. Meaning 10-1iu,20-2iu and so on. Hope that help's. Also vent the gh vial before mixing in the bac water or it will shoot onto the flake from the pressure and can ruin the gh, let it roll down the side of the gh vial and gently swirl it afterwords.

 

[Cauliflower Ear]

huh good to know...i have beeen shootint it

 

[ItalianMuscle27]

I'm tired but i believe this is correct. Use 1ml of bac water with your 10iu bottle of gh,on the slin pin each 10th will be 1 iu. Meaning 10-1iu,20-2iu and so on. Hope that help's. Also vent the gh vial before mixing in the bac water or it will shoot onto the flake from the pressure and can ruin the gh, let it roll down the side of the gh vial and gently swirl it afterwords.

Correct, but no need to vent it. You can simply tilt the vial and let the bac water trickle down the side.

 

[drrman]

ahite bro, these guys are pretty much correct.

draw out 1ml of bac water and insert the needle at a 45 degree angle into the bottle to allow the water to hit the side of the vial then run down into the hgh.

then gently "swirl" the water to dissolve the HGH, do NOT shake it

now, the vial is vacuum sealed so there is a vacuum in there which makes it a bit hard to pull out the water when you go to inject. I usually pull the plunger out of the syringe i used to put the water in there and insert the needle back in to equalize the pressure....is much easier when you go to pull the HGH out now. otherwise you would have to inject air each time to teh HGH to pull some out and this causes air buttles and all that shit, so just equalize it from the get go

now you have 10 iu's HGH per 1ml of water........so on teh insulin syringe 10 iu's will be 1 iu HGH, or 1/10cc will be 1 iu HGH

so to take 2 iu's just pull out to the 20iu mark on your insulin syringe, this will be effectively 1/5 of the total syringe. squeeze up some fat and inject.....its that easy

 

[gunrunner]

ahite bro, these guys are pretty much correct.

draw out 1ml of bac water and insert the needle at a 45 degree angle into the bottle to allow the water to hit the side of the vial then run down into the hgh.

then gently "swirl" the water to dissolve the HGH, do NOT shake it

now, the vial is vacuum sealed so there is a vacuum in there which makes it a bit hard to pull out the water when you go to inject. I usually pull the plunger out of the syringe i used to put the water in there and insert the needle back in to equalize the pressure....is much easier when you go to pull the HGH out now. otherwise you would have to inject air each time to teh HGH to pull some out and this causes air buttles and all that shit, so just equalize it from the get go

now you have 10 iu's HGH per 1ml of water........so on teh insulin syringe 10 iu's will be 1 iu HGH, or 1/10cc will be 1 iu HGH

so to take 2 iu's just pull out to the 20iu mark on your insulin syringe, this will be effectively 1/5 of the total syringe. squeeze up some fat and inject.....its that easy

Thanks Drr!!!