Recent content by deadfred

+1 Steady pressure, All depends on how it flows at the injection site. Forcing it into an area that it doesn't want to go is a sure way to get an abscess. I have had to move mid injection a few times because the area I was in didn't allow the oil to flow into the muscle.

I can't even touch a drop of Tren without feeling like I have permanent hang over. Tren just hits some people that way.

Draw with an 18g, switch to 23g, heat with hair dryer … Needles are cheap, the one problem with amps other than being a pain to open, if you even think you hit the bottom of the glass with the needle you will fish hook the tip.

I can't even look at a vile of BD prop without limping around for a week. I don't know what it is about it but I even tried cutting 1/2 cc BD prop with 1.5 cc of EQ and it still felt like I was walking around with a wood screw stuck in my muscle. I never got red or swollen from it and it took...

I got a bunch of GTP stuff (EQ, Test, D-bol) about a week before he went scammer. Tossed all of it as soon as I found out.

I was 147 lbs at age 23 right when I went into the military (just looked at my medical records). While in the military I did a few 6-9 month runs at the weights but could never break the 170lb mark. Just wish I had read up on diet for body building back then. Now when I got back into the...

My body fat never really changes that much,(been wearing size 32 pants since I was 14) the highest its been was just over 13% and I was just checked using 7-point skin fold at 11.2%. Yes, I basically started cycling as soon as a started in with the heavy weights. Most people would say I should...

I have been doing 500 Sust / 400 Deca for ten weeks and decided to stretch the cycle out another three to start into cutting. I am about two weeks into the cutter and have dropped way back on the carbs and upped my protein intake a bit and it is amazing how much my strength has dropped off...

I am about 3 weeks in on a 750 sust/400 deca cycle and my gains have been very low so far (2 lbs). 99.9 % of the time if I have a problem with gaining it is due to me being light on my diet, but not this time. I was beginning to suspect bunk gear because Sust always has left me a little sore...

Aaaah... now I think I see what the confusion is, its the same stuff you are using. Its 1000mcgs in 1ml solution put in a 2ml vial not in 2ml of solution. In that case everything makes sense. Thanks Tux, now I can stop this madness...

Here is the quote directly from the site: "Each one of our kits comes in a 2ml vial containing 1000mcg of LR3 IGF-1." and the question about 1ml or 2ml was asked and answered by the admin, answer was 2ml...

Yes, I believe that I stated that U100 slin pins are 100 units per cc, so isn't 1 unit = 0.01cc??? I am really not trying to be retarded about this or anything I just want someone to show me the math in how they know that given the equipment listed that 1iu = 10mcg. I am just trying to learn...

Ok say you have the following: a 2ml bottle containing 1000mcg of IGF-1 a 1/2cc U100 slin pin (the most common type) The question is 1iu = xx mcg of IFG-1??? ? ? ? ? The answers I have seen/been given is: 1iu = 10mcg Now every way I have calculated it out I get 1iu = 5mcg (with a U100 pin)...

I just had a pre-employment drug test just coming off the tail end of a Var/Primo/Deca cycle and had just started up with some Clen. The drug test came back negative but my hands were shaking enough that I had a tough time filling out all the employment paper work. Probably should of laid off...

Anyone ever try a Var and Primo stack? I was thinking about 30mg/ED Var and 500mg/wk Primo for cutting, not looking to put on any mass. Or would I be better off dropping the Var and upping the Primo a bit? Currently 205lbs/~12%BF.