Is this recipe correct??

[sjones99]

I have been training for ten years and juicing for five years and I want to try my hand at homebrewing so is this recipe correct and is it missing anything??



As an example, we’ll make an injectable steroid – testosterone enanthate.

To make 40ml @250mg/ml of this steroid, you need:
10 grams hormone (testosterone enanthate)
.08ml Benzyl Alcohol = 2% BA
8ml Benzyl Benzoate = 20% BB
23.2ml oil (grape seed or sesame seed)
Syringes 3cc & 5/10cc
18 or 20 gauge needles
Vial or beaker
Sterile filter

Place powder in vial/beaker. Add BA/BB/Oil to the vial. Heat on Low/Med heat until it dissolves completely. Place the needle in the vial. Place another needle in the vial to relieve the pressure. Draw out solution with a syringe, run though filter. With needle still in the vial, place in oven on a cookie sheet and bake for an hour at 275F degrees.

ANY INPUT MUCH APPRECIATED!!!!

 

[Heath82]

all the numbers are correct

 

[sjones99]

all the numbers are correct

Thanks man, ive been reading some more and does enanthate need the bb or not??

Did the steps look accurate??

 

[Heath82]

no, you dont have to have bb, but since you got your numbers already figured up keep it in there. everything looks accurate, you can do it that way or this way, whichever is easier

• measure 10 grams of powder
• place the powder in the vial
• add BA to the vial
• heat the oil in a suitable container in the oven to a minimum of 212 degrees F to sterilise it (it will likely be necessary to use slightly more oil than listed as you will not be able to utilise all of it)
• add the oil to the vial but save 2 ml of oil in the syringe for later
• gently shake the vial.
• reheat the mixture if necessary by placing the vial in a frying pan and place it on the eye of the stove
• place an 18 or 20 gauge needle in the sterile vial and attach the Whatman sterile filter
• place another needle in the sterile vial to relieve the pressure
• draw out the solution with a syringe and run it though the Whatman filter
• take the other syringe with 2 ml of oil (saved previously) and run it through the Whatman filter into the solution.

 

[cm3rt]

Just wanted to say that I have been looking around for a while for a nice explanation of how this is done and this is the best explanation on how to conjure up some Test Enanthate.

 

[25homes]

heat oil seperatly in oven bake at 275 degree for 20 min to sterilize. cook rest on stove as described. pull oil from oven let cool slightly the add oil to your heated chemicals then filter. try to avoid any extra heat to chemical that is not neccesarry. you dont need bb you could just pull bb out and add that volume to your oil to keep numbers accurate

 

[ceg710]

if you add those up it only comes to 32mL... am i missing something. i thought you would need 40mL of solvent or does the 10g of test e somehow play into this equation? i'm obviously new to this

 

[clozto50]

Of course 10 grams is volume about equal to 1mm/gm! You may want to invest in a hand pump and filter,after awhile you will hate whatman filters.

 

[goin on 4T]

you don't neeed to bake it, that is why its filtered.

 

[PuffDawg]

Personally I like to bake mine when its finished. Not too hot. Just enough to evaporate some of the alcohol-vapors(process of osmosis). It does make less painful injects by baking. We don't have the environment like human grade stuff is made in so we need to use more BA etc to get it sterile. Once its sterile and you bake out some of the alcohols, its still sterile with less alcohol which = less pain. It takes quite a bit of heat to ruin your hormone.