why does my test keep forming crystals?

[binö]

btw, the stuff is pharma grade perscribed to me.
kept it outside in my garage, it got below freezing, and it sludgeified...warmed it back up in water, g2g fairly quickly.
kept in inside in my med cabinet (house is kinda chilly at 62ish) and i go to pin this AM and i see crystals floating around.
wtf?
def not below freezing in my house, the initial time i completely brought it back to a liquid...why is it still crystalizing? does it somehow become prone to it if it happens once?
and does freezing damage it in anyway? my research indicates that it doesn't...
it's test cyp @ 200mgs

 

[needtogetaas]

Your shit is crashed man ..

 

[binö]

Your shit is crashed man ..

but why does it keep crashing after i rejuvenated it?
btw it came back to life with just luke warm water...do i need do more to keep it from crashing, like use hotter water?

 

[bluetwistedsteel67]

It keeps crashing because when it was heated, some of the componant that allows it to become a solution evaporated and now it won't hold. It's the reason that each time gear is heated it becomes more and more likely to crash. My advice is to just keep reheating it each time you draw a dose until it's gone. The alternative is to add some eo or bb but if it's a 10cc vial I wouldn't even bother. Just reheat and use.

 

[UA_Iron]

Just reheat bro.

BA or BB is not going to evaporate from a cooling and heating cycle if its in a sealed container. Pharm grade stuff is on the cusp of being stable anyway with a 0.9% BA content.

 

[needtogetaas]

but why does it keep crashing after i rejuvenated it?
btw it came back to life with just luke warm water...do i need do more to keep it from crashing, like use hotter water?

Once crashed always crashed.

 

[binö]

thanks bros

 

[bluetwistedsteel67]

Just reheat bro.

BA or BB is not going to evaporate from a cooling and heating cycle if its in a sealed container. Pharm grade stuff is on the cusp of being stable anyway with a 0.9% BA content.

once he pushes a needle through the stopper its no longer sealed. BA will absolutely evaporate even in a vial unless it's airtight.

 

[burnthiscorpse]

Do the post crash injections hurt? I had some tren crash on me and after that happened the pins hurt like a bastard. Pre crash it was smooth as butter.

 

[binö]

Do the post crash injections hurt? I had some tren crash on me and after that happened the pins hurt like a bastard. Pre crash it was smooth as butter.

yea it does noticeably hurt a lil.
stupid question, but what would happen if you injected a crystal?

 

[burnthiscorpse]

yea it does noticeably hurt a lil.
stupid question, but what would happen if you injected a crystal?

I pm'd needto about this very same thing way back then when it happened and IIRC he said run it if you can tolerate it.

I did a few cloudy injections then called it quits. The shit fucking hurt.

 

[UA_Iron]

You can try putting .1ml filtered BA into each vial and see if it goes back into solution. Your final dosage would be around 247mg/ml if the gear is dosed right on @250mg/ml.

 

[binö]

You can try putting .1ml filtered BA into each vial and see if it goes back into solution. Your final dosage would be around 247mg/ml if the gear is dosed right on @250mg/ml.

it's @200mg, 10 ml bottle
looking at it today, it appears back into solution...i'll proly just warm it up as needed thanks though

 

[dp40]

Insert a needle in the top of vial-put vial in small pot on the stove-add water to below top of vial-heat to boiling-remove and add .5 cc BB.