Suspending Var?

[dr0832]

I gave up with the var i have been taking... Its gotta be fake. Now I am looking for some directions for suspending var in 151. I know theres a bunch out there but I am no longer platnium and can't search. I am REALLY interested in finding someone thats actually suspended var in 151 that can give me there personal experience and the exact steps to take. I do not want to use everclear, peg400, o BA or Prop Glycol because theres are not readily available.

 

[TraxZBT]

i've tried the 151 route... at 20mg/ml it would go into solution, but once it cooled down it automatically crashed.. From then on I've only mixed it with PG and shook it everytime I dosed. Guess you can do that same with 151.

 

[BBC]

I really don't have any experience using 151, but why don't you experiment a little bit? Start at 15mg/ml, if it doesn't hold, add more 151 and take it down to 10mg/ml. See what happens and report back.

But, bump for people who have actual success at a determined dosage.

 

[chris06749uk]

Try http://www.lemelange.com for Peg 400

 

[kbrkbr]

I have always found it easy to suspend var in 151 at 20mg/ml.

The initial mix always falls out, but then I heat it gently just once and from then in it stays in suspension.

Winny, on the other hand, is virtually impossible to keep in suspension. You have to reheat it every other day.

 

[Lowest]

I had to use everclear to keep it at 20mg/ml bro, it just won't hold that high with 151. Maybe at 10-15mg/ml it might, but var is notoriously hard to dissolve in alcohol.

 

[dr0832]

well can someone give me the exact directions. I am only gonna be taking 30mg a day so either 10 or 15mg/ml would be perfect.

 

[kbrkbr]

well can someone give me the exact directions. I am only gonna be taking 30mg a day so either 10 or 15mg/ml would be perfect.

Okay boys and girls.

The only thing you have to remember is that one gram of powder displaces approximately 1 ml of solution. Oh, and you also have to remember that there are 1000 mg in one gram. So you have to divide the...oh fuck it, I'm just gonna do the math for you. Easier than explaining.

If you want 10mg/ml, dissolve 1gram in 99ml of your solvent, whatever you're using.

15mg/ml 65.5ml
20mg/ml 49ml

Heat up a pan of water and place a bowl upside down in it. Place your eyedropper on the bowl and allow it to heat, swirlling gently until the powders have suspended. Be sure to keep the lid loose enough so that the eyedropper bulb doesn't being to swell.

With the var at these concentrations, you should only have to heat it once.

Having a graduated flask comes in handy for the measuring, but any measuring device should suffice.

 

[dr0832]

Maybe I am an idiot, however I don't quite understand this process. I take a pan of water and fill it 3/4 of the way. Then I take a bowl (glass? size?) and put it upside down in the water? Do I this after the water has come to a boil? Where do I place the powder and the 151 if the bowls upside down? I don't have amps and don't have a way to order them.

 

[Lowest]

You want 10mg/ml, that's an easy number. Take 1 gram of var powder, which occupies appx. 1ml of space. Put the var in a flask, beaker, hell almost anything. Add 99mls of everclear. Heat the solution gently by putting the beaker in warm water and swirling occasionally. Once the powder is all dissolved, bottle it. Now you have 100ml's of var at 10mg/ml. For stronger var, just use less solvent or more solute.

 

[kbrkbr]

Maybe I am an idiot, however I don't quite understand this process. I take a pan of water and fill it 3/4 of the way. Then I take a bowl (glass? size?) and put it upside down in the water? Do I this after the water has come to a boil? Where do I place the powder and the 151 if the bowls upside down? I don't have amps and don't have a way to order them.

Sorry, I wasn't very clear.

THe bowl is merely a platform you place your flask, eyedropper, or whatever on during the heating process.

Here's my method, though lowest's works just as well.

I place one gram of var powder in a glass eyedropper bottle. ThenI measure out, for example, 48ml of 151 in a flask and pour it into the eyedropper. Cap the eyedropper, but don't screw it on too tight.

Place a glass/ceramic bowl upside down in a pan. Fill the pan with hot wat until it covers the bowl by about two inches. Heat the water and place the eyedropper on the bowl. Every 15-20 seconds, give the eyedropper a swirl. Continue until all the powder has gone into suspension. Tighten the lid on the eyedropper and mail it directly to me.

 

[dr0832]

Alight i think I understand. Is it possible to buy a flask and one of the containers with the eye droppers built in at walmart?

 

[kbrkbr]

I don't know. I get my eyedroppers from specialtybottles.com and my graduated flasks on ebay.

 

[Lowest]

I bought my stuff from either getpinz or gearbox. And I jacked some from the chem lab, lol, my lab TA made some incredibly nice bongs out of chemistry glassware

 

[carlsky]

Hey bro, my boy is has liquid var suspension and he liked it a lot when he cycled it. I am not sure how it is suspended but I know it is legit.

 

[Lowest]

Technically, water is polar, alcohol is non-polar. Var dissolves in non-poler solvents, not polar ones. So, it would probably dissolve in any non-polent solvent. Just find one that's not poisonous, is liquid, and is cheap, and you'll have a solvent the has no choice but to taste better than liquid-ass EC!

 

[dr0832]

so no places local have this shit?

 

[kbrkbr]

so no places local have this shit?

Have you bothered looking?

 

[dr0832]

where should I look? i have final exams right now so i don;t have much time.

 

[granby140]

internet searches work wonders for the persons that dont have time

 

[raydogg]

We need more info on homebrew on this board......Any bros with knowlege, and know how should start posting.......

 

[dr0832]

Alright i got what I needed at wallyworld.

 

[Lowest]

I already told you how to do this. I have enough knowledge to start a UG lab, what do ya need to know, lol?