Pinning Question

[Angellico]

I wa planning to go to my doctor with my bottle of gear and a needle just to make sure I was pinning the right way but I got called out of town early so I brought my stuff with me cause imma be gone for 4 months.

Now there is a nurse here but she is married to buddy of mine and this chick does not stop talking about people so I dont want here to know.

Anyways... 1st question

My needle and syringe come in to seperate pieces, now when I attached them do I make sure there is no air in the needle before I start gear extraction from bottle?

2nd Question...

Because my gear is in those 10ml bottles is it best to extract into needle with bottle right side up or upside down?

Im confident I know what to do, but I though it couldnt hurt just to get a 2nd opinion.

 

[ishaq]

yee 1st pins are always scary bro but dont look to much into it youve got the right idea, push the needle onto the syringe from the sides dont take the plastic cap of the needle, make sure its tight the best way to pin out of a mutli dose is to pull back 1cc of air into the syringe and insert it into the bottle holding the bottle upside down, push the air into the bottle and release a bit of pressure of the plunger and the syringe will slowly fill with juice, when you reach your desired amount take the needle out, put away your bottle, put the plastic cap on the needle and pull the needle of by twisting it, then put on the needle your gonna use to inject and push the plunger until the top of the air and a few drops of juice come out the tip of the needle, all what will be left will be the oil in the syringe, choose injection site swab with antiseptic pad and inject away my friend

 

[hyp1]

you have to put the two pieces of the needle together and then push the amount of juice you want to take out of the bottle in as air to break the vaccuum in the bottle.say you're wanting to take out 2cc's you need to push in 2 cc's of air into the bottle before you try and extract any out of it.this will make things tremendously easier.I usually tip my bottles upside down,when taking the juice out,just make sure towards the end of the bottle your needle tip is still inside the liquid,otherwise you'll won't extract anything but air

before injecting make sure there isn't any air in the needle,you can do this by pushing carefully until you see there is no air in the syringe.

make sure you sterilize everything with alcohol by rubbing,the bottle tops,and the injection site

read up on injection sites also
SpotInjections.com



best of luck to you bro!

 

[Angellico]

Is there a reason why u shouldnt inject urself with the same needle u extracted ur juice with?

Also, cant u just stick the needle in and extrace the juice without putting air in the bottle? I always thought air was a bad thing.

 

[Backtobasicks]

Is there a reason why u shouldnt inject urself with the same needle u extracted ur juice with?

Also, cant u just stick the needle in and extrace the juice without putting air in the bottle? I always thought air was a bad thing.

They're different sizes.. You probably
Could inject with it, but it's been blunted going through the top of your vial (not to the naked eye) and will not go in as smoothly etc.
Also if you're using a 19 to draw.. You probably don't want to inject with 19, especially first go (there's not much point). It'll scare you haha.

Air into the vial is to build pressure to draw the oil out easier and maintain a Normal pressure within the vial I thinks.

 

[ishaq]

as above better to switch needles cause it will blunt, AND unless your wiping the top of the vial everytime you use it wich is pointless may iswell just switch to a better shaper more hygenic needle, yes you can just put the needle in and extract the juice putitn air just allows the pressure to make it easier, air is a bad thing inside the syringe but by placing it upside down for a lil while most of it dispears and its only ever small amounts wich is minimal and will not cause damage pinning into the muscle.

 

[BLM Shot]

I don't want to hijack this thread so feel free to tell me to beat it if I am. It seems it has been covered how to draw from a vial. Now what if someone wanted to draw say test from one vial and primo from another, but have it all in one syringe for one inject with the two substances?

I am assuming, for simple math- if someone wanted 1ml of test and 1 ml of primo. Would they then pull in 2 ml of air initially then push 1 ml of the air into the first vial, draw 1 ml then push the other ml of air into vial #2 and then draw 1 ml?

 

[ishaq]

lol nah bro thatd be imposibble lol, just do the usual 1ml of air and when you take out the syringe place it in the other vial and just extract straight away to your desired amount, bare in mind you should only combine oils with oils in the same syringe

 

[BLM Shot]

Thanks for the info. It gave me a chuckle to know you actually laughed at my question. Eh, I am still a noob

 

[ishaq]

haha sorry bro just imagined you trying to do it lol but as always you dont learn if you dont ask and we all have questions that need answering so why not get them answered at a highly knowledgable place!