Just finished my 150mg/ml Masteron homebrew

[SlimJim300]

An hour ago I finished my drostanolone propionate homebrew at 150mg/ml with 2/20% BA/BB. It came together very easily. This is a higher than usual concentration (it's usually at 100mg/ml), so I'll let you guys know whether or not it ends up hurting.

Now I just have to run by the ABC store to get the everclear needed for my liquid var

 

[scout69]

Hey congrats I dont have the patience to make shit myself,Let us know how it works out

 

[|3ossman]

I wish i could brew my own shit, cant with my current living arrangements.

 

[tempest2003]

verry interested, keep us updated

 

[Mr.X]

that's a heck of an amount of BB, you should have just used more BA

 

[Guvna]

that's a heck of an amount of BB, you should have just used more BA

nah, bb is painless. ba, well...



BTW, ive never got var to go into solution any higher than about 10 mg/ml in everclear.

 

[SlimJim300]

It's been over 24 hours since the first inject, and I can say it's completely pain free and holding perfectly in suspension

Hey thanks guvna, I just noticed that last part of your post. Over at IFL they usually throw in PEG to get it to hold solution, but I've heard that glycerol also works. I'll have to keep that in mind.

 

[ALIN]

An hour ago I finished my drostanolone propionate homebrew at 150mg/ml with 2/20% BA/BB. It came together very easily. This is a higher than usual concentration (it's usually at 100mg/ml), so I'll let you guys know whether or not it ends up hurting.

Now I just have to run by the ABC store to get the everclear needed for my liquid var

just out of curiosity what did your raw masteron look like?

 

[SlimJim300]

Like baking soda I guess. It was less clumpy than test prop.

 

[glover]

Congrats, I have some Masteron powder as well to convert. Are you running the Var with it?

I use about 10cc peg 400 with the rest everclear to hold my 10mg/ml var it does good just does not completely dissolve but almost.

 

[psychedout]

nah, bb is painless. ba, well...



BTW, ive never got var to go into solution any higher than about 10 mg/ml in everclear.

This is a common misconception. BB can and will cause pain in 15-20% and higher concentrations. The factor determining this is really individual tolerance.

Trust me on this. I one had the idea to create a solution using 50% bb to make is very thin so it would flow easily through a slin pin. And well, it did do that, but holy fuck did it leave some nasty pain after. That went down the drain -- big waste of cash.

 

[SlimJim300]

Congrats, I have some Masteron powder as well to convert. Are you running the Var with it?

I use about 10cc peg 400 with the rest everclear to hold my 10mg/ml var it does good just does not completely dissolve but almost.

Yes I'll be running the var with it. How many mls total solution did you make for that?

 

[lurcan]

I ususally use 150mg a day of mast, 100mg of mast e and 50 mg of mast p. I'v hade no problems and it's ripped me up pretty good. Granted I use a lot of gear to protect my hair, which is not falling out, even if I use it with Winny d(Test is a given, I never do cycle without it) and Tren. I swear I'm not bullshittinng you. One day I'll post pix of the hair both before and after.

 

[glover]

Yes I'll be running the var with it. How many mls total solution did you make for that?

Sorry for the lack of details. I use 10 mls PEG 400 and 39 mls Everclear for 50 mls of 20mg/ml Var. Not the 10 mg/ml I stated earlier that was incorrect. Stays in solution pretty good. But after cooking I can never get 100% crystal disolve, probably 85-90%.

 

[SlimJim300]

Thanks glover, good info. Can you get it to hold at 20mg/ml when you use the PEG, or does it fall out of both the solutions you made?