Heating up Winny...

[flyin j]

Ive read QV winny can hurt like hell when injected and ive also read on some threads that if heated it doesnt hurt at all if this is true whats the best way to heat it up and how much pain is there in injecting in the quad and shoulder because i am constantly walking and picking things up at work i can tough it out to a point ive done it before but i dont want to draw attention to my limp or dead shoulder.

 

[Breeze]

Run the loaded syringe under hot tap water for a minute or two. This will thin it a little and help it inject smoother.

 

[flyin j]

Run the loaded syringe under hot tap water for a minute or two. This will thin it a little and help it inject smoother.

thanks, ive taken test, fina and eq in the quad and been ok with walking but ive heard bad things about winny in the quads and delts any experience there???

 

[Breeze]

thanks, ive taken test, fina and eq in the quad and been ok with walking but ive heard bad things about winny in the quads and delts any experience there???

Never had a problem, but the last winny I injected was upjohn which was smooth as silk. A lot of the pain will depend on your personal tolerance and the brand you use.

 

[mrplunkey]

My sekrits to winny success:

1) Shake the mortal hell out of the vial before you draw it

2) Heat-up a microwave heating pad -- hot, but not scalding.

3) Draw-back on the syringe to leave a nice 1-2 ml air pocket in the syringe. Place capped syringe on the heating pad and fold it over.

4) Wait a full 2ish minutes. Prep the injection site. Remove the syringe from the heading pad, eliminate the air, shoot winny.

5) Massage the hell out of the area afterward. Brookstone "Max" oscillating massager > All

I suspect that I'm "boiling off" the alcohol from the winny, but to be honest I'm not entirely certain how or why this technique works. I don't like using water-based solutions (i.e. submerse syring in hot water and/or underneight running water) because I'm never sure where the water is going.

Hope this helps!

 

[flyin j]

My sekrits to winny success:

1) Shake the mortal hell out of the vial before you draw it

2) Heat-up a microwave heating pad -- hot, but not scalding.

3) Draw-back on the syringe to leave a nice 1-2 ml air pocket in the syringe. Place capped syringe on the heating pad and fold it over.

4) Wait a full 2ish minutes. Prep the injection site. Remove the syringe from the heading pad, eliminate the air, shoot winny.

5) Massage the hell out of the area afterward. Brookstone "Max" oscillating massager > All

I suspect that I'm "boiling off" the alcohol from the winny, but to be honest I'm not entirely certain how or why this technique works. I don't like using water-based solutions (i.e. submerse syring in hot water and/or underneight running water) because I'm never sure where the water is going.

Hope this helps!

Thats the route i will go but why draw in the air, and thanks for that info.

 

[mrplunkey]

Thats the route i will go but why draw in the air, and thanks for that info.

I noticed that if you didn't put a little air in, the heating action pushed some of the winny through the needle and into the needlecap. My guess is that when the alcohol boils-off, it needs a little airspace to move into or it takes some winny with it.

Also, I like having some room in the syringe to shake it one last time before I shoot.

 

[flyin j]

I noticed that if you didn't put a little air in, the heating action pushed some of the winny through the needle and into the needlecap. My guess is that when the alcohol boils-off, it needs a little airspace to move into or it takes some winny with it.

Also, I like having some room in the syringe to shake it one last time before I shoot.

thanks, those are the kinds of answers i cant find around my area.

 

[Makavelli]

So by burning the alcohol off there is less pain....I'll let you know in a few weeks..

 

[flyin j]

So by burning the alcohol off there is less pain....I'll let you know in a few weeks..

Yeah let me know because im buying it this week and wont start for a month or two.

 

[TheAssholeFomerlyKnownAsDBBT]

Ive read QV winny can hurt like hell when injected and ive also read on some threads that if heated it doesnt hurt at all if this is true whats the best way to heat it up and how much pain is there in injecting in the quad and shoulder because i am constantly walking and picking things up at work i can tough it out to a point ive done it before but i dont want to draw attention to my limp or dead shoulder.

I fill up a 20oz shaker of water, nuke it for 2 min. then throw the loaded dart in to it, needle up and let sit for about 4 minutes...QV gear has crystals that can hurt like a BITCH if you dont heat to help dissolve those before inj.

 

[Makavelli]

I fill up a 20oz shaker of water, nuke it for 2 min. then throw the loaded dart in to it, needle up and let sit for about 4 minutes...QV gear has crystals that can hurt like a BITCH if you dont heat to help dissolve those before inj.

So is it dissolving the crystals that attenuates the pain or burning off the alcohol?