Re: Fina Farm now has kits to convert Powders!
www.FinaFarm.com
"Universal Kits"
** Information below has only been tested on Finafarms Universal kits. Using
these
directions with any other companies kits may not work and could ruin your
experiment***
Kit includes (sesame oil, benzyl alcohol,and benzyl benzoate mixture)
Universal kits are used to convert many types of powders.
Break down of the kits are as follows. (Kits can do a variety of powders, we
have
listed the most popular.)
5 Gram Universal 200 Kit...(this can be used with test enanthate or cyp,
tren enanthate, boldenone undecylenate (EQ), nandrolone deconoate (deca))
***This kit will convert 5 grams of longer lasting powdered aromas into
a sterile solution @ 200mg/ml. (Kit will yield a final product @
25ml@200mg/cc)***
10 Gram Universal 200 Kit...(this can be used with same as above)
***This kit will convert 10 grams of longer lasting powdered aromas into
a sterile solution @ 200mg/ml. (Kit will yield a final product @
50ml@200mg/cc)***
5 Gram Universal 100 Kit...(this can be used with test base, test
propionate,tren acetate.)
***This kit will convert 5 grams of fast acting powdered aromas into
a sterile solution @ 100mg/ml. (Kit will yield a final product of
50ml@100mg/cc.)***
10 Gram Universal 100 Kit...(this can be used with same as above)
***This kit will convert 10 grams of fast acting powdered aromas into
a sterile solution @ 100mg/ml. (Kit will yield a final product of
100ml@100mg/cc.)***
Benzyl Benzoate is included in our kits and here is why...Benzyl
Alcohol(BA) is good for
its bacteriosteric properties and is a good dissolver. Benzyl Benzoate (BB)
on the other
hand while not bacteriosteric, holds powders in solution better than
BA and will lower the overall viscosity of the oil. The BB in the kits will
also prevent the solution from crashing, which means the powder will not be
suspended in the
mixture. **Note, our kits have a low BA content, around 5% so our kits
wont be
"painfull" when used**
THE FUN PART ****INSTRUCTIONS*****
Make sure all supplies are available and clean your area well. I like to
wash my hands in 70% rubbing alcohol and only touch my supplies during
conversion.
Remove top circle of metal seal from bottle with solution.
Take your 3cc syringe and draw out exactly 1.5cc and place cap back
on needle and set aside.
Now remove the rest of the metal seal and rubber
stopper from vial with solution.
Use funnel or other device and add
required powder directly to solution.
Gently swirl together until
nice and clumpy. Place a pan on an eye of the stove and turn burner
to medium not high heat.
Add enough water to pan to cover .25 inch on
bottom of pan. Place vial with solution in pan and heat for about one
minute with the rubber stopper off.
Grab top of vial and gently swirl
solution. Keep adding medium heat this way until all the powder dissolves.
*Hint-If you can't grab the top of the vial because it is too hot than
you need to lower the burner temperature**. Now that it is dissolved place
the rubber stopper back on top and while holding the stopper in place
gently shake the solution to ensure all of it is mixed thoroughly.
Allow solution to cool for about 5 minutes. While it is cooling remove
the center section of the aluminum top on the empty vial but not the
entire aluminum seal. Clean off the top of the rubber stopper with rubbing
alcohol and insert two of the 18g needles.
Pay close attention to not touch the needles with your hands. Place the Whatman filter on
top of one of the needles. Do not touch the tips on the filter only
the sides. The other needle is there to allow air to escape. Attach
final 18g needle to the 10cc syringe and draw out 10cc of the
warm solution. Now use the cap off the needle and remove needle from
syringe. Now hold the syringe facing up and let any trapped air out.
We are going to pre-wet the filter to make it easier to filter. With
the needle and filter still in the empty vial, attach 10cc syringe to
Whatman and turn vial upside down and slowly fill the filter with solution.
This will help remove any trapped air inside the filter. As soon as
you see solution drip out of the tip of the needle turn right side up
and gently press plunger and filter solution into vial. When you finish
filtering solution remove syringe from needle and put other needle back
on and draw up more solution and repeat until done.
***You could heat in oven but I feel that with proper BA(Benzyl Alcohol)
ratio
there should be no problems. Also as I am sure you know when you heat them
in the
oven and vent them with needle you get a permanent hole in your stopper.
I suggest using a slin pin if you decide heat in the oven so the hole is not
an
issue but the slin pin is NOT included in the kits.***
****Enjoy your powder therapy.****
Please Scroll Down to See Forums Below 
