boiling out b/a

[anomaly]

Allright I posted a while a go about the ttokkyo cyp that I had
giving me horrible fevers for about two days, along with huge
swelling in the site where I hit. The consensus was that it was the high benzol alcohol content in the cyp. A guy in the gym the other day told me that one way of dealing with this was to put a dart in the top of the bottle, put the bottle in some boiling water, and then the benzol alcohol would be burned out (evaporated) of the solution, thus getting rid of all the benzol side affects. So does this work , and if it does, then does it disrupt the chain of the cyp making it no longer a potent substance? Thans for any help. Oh yeah I'm calling for a 37-10 Raiders win!

 

[Zyglamail]

And chances are if you get totally rid of the BA you will also have cyp falling out of suspension and laying on the bottom of the vial. Your best bet is to do one of two things, stick with a quality painless gear or add a painless gear to your painfull stuff, something like EQ or deca seems to mellow it out a lot.

 

[anomaly]

Hey Zyg, in the future I will definately use other products. But right now I have 40 ccs left of this cyp and can't part with it. Wouldn't I be able to after boiling just be able to shake up the bottle like a bottle of winny before drawing to make sure that I'm getting an evenly diluted solution?

 

[Zyglamail]

Its up to you, can try it but if it does precipitate then there is now way to be sure your getting a relaible dosed inj.

 

[The Bigfella]

As it does not boil until 206 degrees C, placing in boiling water does not burn off the high BA bro.

http://www.noveoninc.com/products/kalama/bzlcmsdn.htm

It can be baked a few times and have heard of some getting good results, although it usually still stings, but personally would recommend going with a better manufactured steroid next time bro

Bigfella.

 

[Spidey]

As it does not boil until 206 degrees C, placing in boiling water does not burn off the high BA bro.

http://www.noveoninc.com/products/kalama/bzlcmsdn.htm

It can be baked a few times and have heard of some getting good results, although it usually still stings, but personally would recommend going with a better manufactured steroid next time bro

Bigfella.

What he said. BA has a higher boiling point than water so whoever told you that works is a moron.

-Spidey

 

[anomaly]

Thanks for the help, looks like I'm just gonna have to scrap it.

 

[chickmagnet]

hey, i had the same problem with ip shit. Huge lumps, and fuckin pain....nothing worked until i put it on a spoon and boiled it with a lighter, then let it cool and sucked it up into the syringe. It sucks doing this for every shot, and it makes you look like a crackhead, but it works....

 

[Spidey]

hey, i had the same problem with ip shit. Huge lumps, and fuckin pain....nothing worked until i put it on a spoon and boiled it with a lighter, then let it cool and sucked it up into the syringe. It sucks doing this for every shot, and it makes you look like a crackhead, but it works....

At least this could conceivably work. Even though BA boils at 206 C, it is still the lowest boiling component in the mixture. If you boil it on a spoon over a flame, you might be able to evaporate some of the BA. You may also damage the gear though.

-Spidey

 

[Johnny Cut]

would increasing the oil concentration aid in site irritation reduction, for example pulling an extra CC of oil from say a bottle of sesame oil and mixing it with your painful gear help, yes it would make a 1 cc injection into a 2cc injection, but u would have less pain and proper dosage,....well as proper as u could get with ttokkyo crap

 

[The Bigfella]

would increasing the oil concentration aid in site irritation reduction, for example pulling an extra CC of oil from say a bottle of sesame oil and mixing it with your painful gear help, yes it would make a 1 cc injection into a 2cc injection, but u would have less pain and proper dosage,....well as proper as u could get with ttokkyo crap

Yep, it is better to mix with any other steroids as well as this also dilutes the BA content overall in the shot and eases the pain a little.
You can bake it without ruining but do not boil it, it will still give of BAvapours at below the boiling point, which will help a little, then just dilute with other oil or a combo with another steroid. Better than wasting it bro..........

Bigfella.

 

[swampmoose]

re

if your getting sick, you might want to try supplementing with a few grams of vitamin C or other antioxidants. C is the cheapest and does wonders for me. havent been sick since. IMO

 

[Sigmund Roid]

Ok, here is the solution:

Oil, BB and your steroid are very poorly soluble in water, but water can handle 4% BA. So what you do is to poor water on your oil, say you have 10 ml 10% BA, that is 1 ml BA, you need 25 ml water. Preferably the water is sterile and contains some NaCl (table salt), say 1.25 grams in 25 ml water. You shake very very well and wait for separation. Then you take out the oil fraction, and viola, you have what you need. There will still be some BA in the oil, but a lot less.

BTW, if too much BA is taken out of the oil, your steroid might precipitate and you don't want that! Maybe start with 10 ml water per 10 ml oil?

 

[Spidey]

Ok, here is the solution:

Oil, BB and your steroid are very poorly soluble in water, but water can handle 4% BA. So what you do is to poor water on your oil, say you have 10 ml 10% BA, that is 1 ml BA, you need 25 ml water. Preferably the water is sterile and contains some NaCl (table salt), say 1.25 grams in 25 ml water. You shake very very well and wait for separation. Then you take out the oil fraction, and viola, you have what you need. There will still be some BA in the oil, but a lot less.

BTW, if too much BA is taken out of the oil, your steroid might precipitate and you don't want that! Maybe start with 10 ml water per 10 ml oil?

That is a sound idea. Why didn't I think of that.

-Spidey

 

[Punt]

bump this up

 

[Punt]

This is a recurring topic, lets hear some more input/thoughts.

 

[Spidey]

I think Sigmund answered the question quite nicely. It's hard to imagine a better or easier solution than he gave.

-Spidey

 

[Mr. Las Vegas]

I have had this problem with Mexican gear before. What I did was: Fill the syringe with the steroid. Take off the needle and stick a toothpick in the hole where the needle goes. Microwave it on high for 45 seconds, then run it under cold water until it cools. Heat and cool it three times and it should be fine.