Baking out the BA: QUESTION!

[maddawgxxl]

As I watched my vial cooling... I could see that air was going through the vent pin back in to the vial (cause there were tiny bubbles at the tip of the pin going inwards)...

So... I'm baking out the BA which makes the product sterile AND now I'm allowing all the crap in the air to get sucked in to my vial... ready to shoot in my body?

Am I missing somthing??? I covered my vial with a sanatized (alcohol) glass, but only after I realized what was happening.

Is this gonna be OK???

 

[marshallmadman]

Yeah, you're fine. You didn't cook out ALL the b.a. just some of it.

 

[maddawgxxl]

OK... I pictured a little fruit fly from my bananas getting sucked in to the vial and then getting injected into my arse!!!

 

[FlexManning]

I know that the baking method is pretty widespread, but I have to tell you all again that most of the well known fina kit suppliers like finafarm don't recommended baking at all. Just my two cents.

 

[bilter]

you lost very little BA. IT has a boiling point of 403 degrees F.

 

[maddawgxxl]

I used the method that has been discussed here time and time again. Apparently, you're not trying to boil the BA just speed the evaporation process.

One difference I can tell IMMEDIATELY is that before the baking... I would feel the burning pain as the oil was injected (and I've been doing this for over 10years so I'm injecting correctly)... after the bake... it went in smooth. Didn't feel it at all.

It seems there is a lot of problems with the BD Test E having a high concentration of BA. Doing the baking procedure helps remove some of that and seems to solve the problem. I'll be posting a follow up as tomorrow will show the true results!!

 

[Ulter]

I used the method that has been discussed here time and time again. Apparently, you're not trying to boil the BA just speed the evaporation process.

One difference I can tell IMMEDIATELY is that before the baking... I would feel the burning pain as the oil was injected (and I've been doing this for over 10years so I'm injecting correctly)... after the bake... it went in smooth. Didn't feel it at all.

It seems there is a lot of problems with the BD Test E having a high concentration of BA. Doing the baking procedure helps remove some of that and seems to solve the problem. I'll be posting a follow up as tomorrow will show the true results!!

Yes, that's right. You're just causing evaporation and it works. As you've seen.

 

[aluv4speed]

How exactically do you go about baking it? I am starting my test e tomorrow and would like to know what to do. If anyone could please descrive the steps I need to take to bake....thanks....

 

[linux]

Whats the standard temperature for "baking" When i get back to the lab on monday ill set up and experiment and see if this baking out the BA thing works..im thinking it doesnt..but well see

 

[marshallmadman]

Do not bake. Do a hot water bath instead. Put your vial, with a pin in the top to vent the gasses, in a pan of boiling water. The water level should be just enough to not float the vial. About 3 quarters of the vial should be submerged. Boil for 5 minutes, let it cool, draw, and shoot.

 

[maddawgxxl]

According to past posts....

Put a pin in the vial for venting but don't touch the oil.
Wrap a bit of foil around the stopper to keep heat away from rubber (optional)
Put vial in oven at 175 degrees for 10 minutes
Take out and cool for 20-30 minutes
Repeat 2 more times

I did it and the injections were like night and day! I don't need science to back this one up... my body gave me the answer!!!

 

[aluv4speed]

awsome...I will try this. I just want things to go as smooth as possible you know....

any other feedback on this>?

 

[Fukkenshredded]

There is no need to bake at all. As pointed out already, the boiling point of BA is over 400 degrees.

 

[bilter]

According to past posts....

Put a pin in the vial for venting but don't touch the oil.
Wrap a bit of foil around the stopper to keep heat away from rubber (optional)
Put vial in oven at 175 degrees for 10 minutes
Take out and cool for 20-30 minutes
Repeat 2 more times

I did it and the injections were like night and day! I don't need science to back this one up... my body gave me the answer!!!

if you use this method preheat the vile in a cup of very hot water (boil it the remove from the burner, then let the vile sit in it for 5 minutes). Why you ask? This will insure that the vile will reach the oven temp and stay there for the 10 miutes that you have it in the oven