Please Scroll Down to See Forums Below
napsgear
genezapharmateuticals
domestic-supply
puritysourcelabs
UGL OZ
UGFREAK
napsgeargenezapharmateuticals domestic-supplypuritysourcelabsUGL OZUGFREAK

Primo 200mg/ml Possible? Is 2/15 good enough

black sheep

Banned
Has anyone made Primo at 200mg/ml. I want to run a gram a week cycle and don't want to have to take 10cc's a week. I also don't want a painful injection site either so that is a consideration.

I was thinking the following for the conversion:

34ml Of grapeseed oil
10 Grams of Primo powder
1ml of BA
7.5ml of BB


Thanks in advance
 
Okay I just made a hybrid:

200mg/ml Primo
20mg/ml Test (To supplement suppressed natural levels)

I made it 2/18 and used 50% Grapeseed and 50% EO. I will let you know in a couple days if it is painful or not.
 
black sheep said:
Okay I just made a hybrid:

200mg/ml Primo
20mg/ml Test (To supplement suppressed natural levels)

I made it 2/18 and used 50% Grapeseed and 50% EO. I will let you know in a couple days if it is painful or not.

Very interesting hybrid. Look forward to the results.
 
black sheep said:
Okay I just made a hybrid:

200mg/ml Primo
20mg/ml Test (To supplement suppressed natural levels)

I made it 2/18 and used 50% Grapeseed and 50% EO. I will let you know in a couple days if it is painful or not.


That sounds bad ass!
 
It turned out very thin. It should inject very easily. I will be using 25ga pins so I will let everyone know the results.

I am not starting until April, but my buddy is starting Monday. He is my Guinne *SP pig.
 
black sheep said:
Okay I just made a hybrid:

200mg/ml Primo
20mg/ml Test (To supplement suppressed natural levels)

I made it 2/18 and used 50% Grapeseed and 50% EO. I will let you know in a couple days if it is painful or not.


Okay, Buddy took first injection of this this AM. No pain whatsoever so far. I will keep everyone posted tomorrow.
 
I've made several batches of 200mg/ml primo with just 2/15 and plain grape or cottonseed oil, no EO needed. None have ever crashed out, and pain is minimul if any for most. I think primo could easily be done 3-400mg/ml with 3%BA and EO as the primary carrier, it's an enanthate ester so it shouldn't be that hard to dissolve.
 
Today is day after injection. My Buddy reports no pain. He can tell that he took 2.5 cc to the glute, but now pain. He has a desk job and sits on his ass all day, and said he was not bothered by it at all today.

It also goes through a 25ga pin very easily.
 
black sheep said:
Okay I just made a hybrid:

200mg/ml Primo
20mg/ml Test (To supplement suppressed natural levels)

I made it 2/18 and used 50% Grapeseed and 50% EO. I will let you know in a couple days if it is painful or not.


Hey, did you make that hybrid seperatly and then combine the two products into one vial or did you use both powders in the same beaker with the BA/BB? I want to make a hybrid of test prop 100mg/primobolan 100mg and masteron 100mg so I can inject one cc every 3 days and have the 3 medicines shot into me at once. I don't know if you can get the suspension right if you mix 3 powders in one beaker, so I was leaning towards putting an equal amount of each into a vial.
 
Para_Shoot said:
Hey, did you make that hybrid seperatly and then combine the two products into one vial or did you use both powders in the same beaker with the BA/BB? I want to make a hybrid of test prop 100mg/primobolan 100mg and masteron 100mg so I can inject one cc every 3 days and have the 3 medicines shot into me at once. I don't know if you can get the suspension right if you mix 3 powders in one beaker, so I was leaning towards putting an equal amount of each into a vial.


Mixed powders and disolved in BA/BB
 
black sheep said:
Okay I just made a hybrid:

200mg/ml Primo
20mg/ml Test (To supplement suppressed natural levels)

I made it 2/18 and used 50% Grapeseed and 50% EO. I will let you know in a couple days if it is painful or not.
so is this recipie legit? how many others have tried it since? any success? thanks for the info
 
I made Primo at 2/20 at 200mg and that was absolutely painfree, I even did quad shots with it and I couldnt even tell I had done the shot the next day..

I have made at 250mg and I mucked up the calcs and used 5% ba and 20% bb, now that bloody hurts.. I think if I had used 2/20 that would have been painfree also..
 
black sheep said:
Okay I just made a hybrid:

200mg/ml Primo
20mg/ml Test (To supplement suppressed natural levels)

I made it 2/18 and used 50% Grapeseed and 50% EO. I will let you know in a couple days if it is painful or not.


Does this mean you got 200mg primo and 200mg test in each 1 cc? I mean, when you take 200mg primo and 200 mg test in one shot, do you have 1 cc or 2?

Sorry, just a little confused . . .
 
Top Bottom