Please Scroll Down to See Forums Below I have a 4g kit and 2 carts. I pulled exactly 30 cc's of tren away from the binders, and then purged two more cc's through the filter.I follow the directions step by step evertime and get the same product. I did this once before and a bro said my concentration was alot higher. Like 110-120 mg per ml. What do you guys think? Anyone else have this problem? thanks
WTF!! Why does my 4g fina kit only yield 32cc
- Thread starter deez
- Start date
J
Johnny Cut
Guest
how many cc's do u other bros get out of the kit
the mechanic
New member
It depends on whose kit you are using, how long you let it separate...a few variables involved.
02gixxersix
New member
Yea when i did mine I got like 42 cc's I think. Oh well thats just how much I needed so it worked out good.
Stillgoing
New member
I just got 40-42 ccs. Just enough to run for 6wks....
Deez, if you filtered everything in the mix including the bottom stuff ( the precipitation at the bottom can be also filtered with the WHATMAN 0.45um if you warm it up in boiling water pot about five minutes or so) then you should have all the tren you can extract, then all you need to add it is 20 cc of flax oil ( you get this at you local food store) then you will have about 75ML/1cc. their could be two possible explanation for you low yield, you left too much unfiltered stuff behaind or they shorted you on oil.
J
Johnny Cut
Guest
the mechanic said:
I was thinking about our good friends at Research, what does everyone get out of those, say the 2g kit?
J
Johnny Cut
Guest
xxx
drgoodbody
New member
well...
If the volume of the end product is less than 40ml and you started with 2 carts (4000mg) and 40ml of oil + dissolving solution then here's the math:
Initial solution: 4000mg/40ml = 100mg/ml of TA injectible
Then you filtered, heated, baked, whatever and at the end got out only 32ml of solution. Well, the only way to have the concentration go higher (above 100mg/ml) is to have evaporated some of the dissolving soln (BA/BB prolly) and assuming that 3-5ml of that is what was in your kit (likely) then the best you could hope for is:
Final solution: 4000mg/35ml = 114mg/ml of TA injectible
But most likely the difference between the 32 that you got out and the 40 that you put in is due to spillage, absorbtion by the coffee filters, Whatman, etc... So it is very likely that your end solution is somewhere between 100-115 mg/ml.
DrG
If the volume of the end product is less than 40ml and you started with 2 carts (4000mg) and 40ml of oil + dissolving solution then here's the math:
Initial solution: 4000mg/40ml = 100mg/ml of TA injectible
Then you filtered, heated, baked, whatever and at the end got out only 32ml of solution. Well, the only way to have the concentration go higher (above 100mg/ml) is to have evaporated some of the dissolving soln (BA/BB prolly) and assuming that 3-5ml of that is what was in your kit (likely) then the best you could hope for is:
Final solution: 4000mg/35ml = 114mg/ml of TA injectible
But most likely the difference between the 32 that you got out and the 40 that you put in is due to spillage, absorbtion by the coffee filters, Whatman, etc... So it is very likely that your end solution is somewhere between 100-115 mg/ml.
DrG
the mechanic
New member
Johnny Cut said:
On his kits I have only made the 4gf (plenty of them !) and done properly have always yielded no less than 46 ml...with the norm being approx. 48 ml.
the mechanic
New member
Sorry Johnny, I mis-read your question. I have never used Research kits, just A`s.
totallyjacked
New member
I have made at least six kits and used research's kits. I have always been dissapointed with the results. I have always yielded from 34 to 42cc with the kits. I don't understand why the fuck it is so hard to include the right amount of oil to yield the correct concentrations. FUCK KITS I am no longer using them. I am going to reuse my syringe filters by cleaning them with acetone and I am going to use vegetable oil from the grocery store which is pure soybean oil (look at the ingredients) this way I can get exactly the concentrations needed, instead of way overpaying for a shitty kid that isn't very good. I think that my kit should not cost more than 3 dollars. For all of you saying "what about sterility" I am going to pastuerize at 170 degrees for 30 minutes and I should be good to go!
GPZ the best kits going if u ask me.. good $, fast cheap sometimes FREE shipping, excellent combo specials, I have used the 2g kit, 4g, and 10g all with excellent results. (2000mg tren = 20ml everytime) (10,000 tren = 100ml every time) great people over there as I'm sure those who have used them agree..
Similar threads
