what do i need to filter gear????Need help!!

[bodybuilder63]

What do i need guys? sealed vial, whatman filter, grapeseed oil?? i have rubber in my gear and i need to transfer to another vail can anyone give instructions???Please help need to order stuff asap

 

[SuperStrong]

grapeseed oil?? not sure why you would need that to filter..

basically you just transfer your aas to another vial, the whatman filter filters out any unwanted particles...

#1) get a 10ml Syringe
#2) a 18g or 20g needle for drawing
#3) the whatman (.45u size i believe)
#4) get a 10ml *presealed vial*
#5) 20 or 22g needle for transferring.
#6) the same size needle for venting.

steps:
1) draw the the aas you want to transfer into the 10ml syringe.
2) remove needle when done drawing
3) screw whatman into the syringe
4) next, screw the 20-22g needle into the whatman.
5) inject "vent" needle of same size into the vial.
6) inject your 10ml syringe into the vial, then start pressing on the whatman and it will drip out your aas into the new vial

*u need vent needle to equalize pressure, as you put in liquid air will escape from the vent needle
*make sure the vent needle never touches the liquid or else the liquid will spray out of the vent needle.
* when you are finished injecting whatever amount, in the end there will be some left over solution on the whatman filter. you just have to draw some air and then start injecting the air and the solution will leave the whatman filter.

 

[KeepinMyGains]

grapeseed oil?? not sure why you would need that to filter..

basically you just transfer your aas to another vial, the whatman filter filters out any unwanted particles...

#1) get a 10ml Syringe
#2) a 18g or 20g needle for drawing
#3) the whatman (.45u size i believe)
#4) get a 10ml *presealed vial*
#5) 20 or 22g needle for transferring.
#6) the same size needle for venting.

steps:
1) draw the the aas you want to transfer into the 10ml syringe.
2) remove needle when done drawing
3) screw whatman into the syringe
4) next, screw the 20-22g needle into the whatman.
5) inject "vent" needle of same size into the vial.
6) inject your 10ml syringe into the vial, then start pressing on the whatman and it will drip out your aas into the new vial

*u need vent needle to equalize pressure, as you put in liquid air will escape from the vent needle
*make sure the vent needle never touches the liquid or else the liquid will spray out of the vent needle.
* when you are finished injecting whatever amount, in the end there will be some left over solution on the whatman filter. you just have to draw some air and then start injecting the air and the solution will leave the whatman filter.

Nice post bro

 

[cuts82]

grapeseed oil?? not sure why you would need that to filter..

basically you just transfer your aas to another vial, the whatman filter filters out any unwanted particles...

#1) get a 10ml Syringe
#2) a 18g or 20g needle for drawing
#3) the whatman (.45u size i believe)
#4) get a 10ml *presealed vial*
#5) 20 or 22g needle for transferring.
#6) the same size needle for venting.

steps:
1) draw the the aas you want to transfer into the 10ml syringe.
2) remove needle when done drawing
3) screw whatman into the syringe
4) next, screw the 20-22g needle into the whatman.
5) inject "vent" needle of same size into the vial.
6) inject your 10ml syringe into the vial, then start pressing on the whatman and it will drip out your aas into the new vial

*u need vent needle to equalize pressure, as you put in liquid air will escape from the vent needle
*make sure the vent needle never touches the liquid or else the liquid will spray out of the vent needle.
* when you are finished injecting whatever amount, in the end there will be some left over solution on the whatman filter. you just have to draw some air and then start injecting the air and the solution will leave the whatman filter.

Thats a solid post bro

 

[HAYEZ]

id use the .22 whatman to filter it not the 45
i wouldnt use a 18 your gonna get chunks of the stopper again use a 20
after all oil is transfered to new vial i would put 2ml of grapeseed oil int he 10ml syringe and flush the filter with that..the filters can hold about 2ml fo oil so you rish losing 20% of your vial in it

 

[ALIN]

grapeseed oil?? not sure why you would need that to filter..

basically you just transfer your aas to another vial, the whatman filter filters out any unwanted particles...

#1) get a 10ml Syringe
#2) a 18g or 20g needle for drawing
#3) the whatman (.45u size i believe)
#4) get a 10ml *presealed vial*
#5) 20 or 22g needle for transferring.
#6) the same size needle for venting.

steps:
1) draw the the aas you want to transfer into the 10ml syringe.
2) remove needle when done drawing
3) screw whatman into the syringe
4) next, screw the 20-22g needle into the whatman.
5) inject "vent" needle of same size into the vial.
6) inject your 10ml syringe into the vial, then start pressing on the whatman and it will drip out your aas into the new vial

*u need vent needle to equalize pressure, as you put in liquid air will escape from the vent needle
*make sure the vent needle never touches the liquid or else the liquid will spray out of the vent needle.
* when you are finished injecting whatever amount, in the end there will be some left over solution on the whatman filter. you just have to draw some air and then start injecting the air and the solution will leave the whatman filter.

Good info bro,,,you laid it out simple for him. Good work.

 

[bodybuilder63]

thanks bro thats everything i needed to kno appreciate it

 

[SSMbigboy]

Do u need to heat your gear before u filter it?

 

[virek80]

If it's viscous (very thick) heating might help. Just fill a sink with hot water and put the vial in there for 10 minutes if transferring from one vial to another). If filtering a homebrew, you could heat it slightly which will make filtering go faster.

Be careful with heating tren though, because too much heat will degrade it.