Water Bubbles In Bottles Make For A Cloudy Condensation Look, Danger or Harmless?

[monte45]

Some one Must Know What Is Happening?

--------------------------------------------------------------------------------

I just recently got my gear in a couple days ago and transfered it
into vials Yesterday. This time I didnt order new sterile vials and open them from a factory sterile package I had
them left over from the last fill that were factory steriilized just extras that i didn't end up using, I had saran wrapped them and left some where for a couple months, so i felt the need to re-sterilize. I boiled the bottles and put
them upside down to dry, to what i thought would sterilize them.
Now they look like there is condensation in the bottles, with
little air bubbles in the vials some more than others.Not anything
too crazy at all, also some turning cloudy. I'm assuming
because of the water damage. I basically didn't let all the boiled
water drip dry out. I was not thinking, oil, water hmm dosn't
mix.(I know, douche bag ) Big rookie mistake and i had just filled
them up not realizing it until I wiped down allll of them at the
end. Is this terrible or am i ok, ive been googling all night and
cant find a definitive awnser. I have a bunch for friends that went
in with me and the last thing I want to do is give any one an
infection or abcess. It is what should be sterile water from being boiled.So i had to be the guinea pig, I took my worst
looking bottles (cloudy and with Water Bubbles*pics below*)and
stuck 1 ml in one cheek and stuck a 1ml from bottle #2 in the other
cheek...Only time will tell, but that was last nite and i dont feel any soreness or discomfort at all. Now do you think over time bacteria
will grow in the water? And does the water disturb the makeup of
the product hence the cloudy effect to them, and or if you know any other harmful effects of this
error. If Anyone can give me a better understanding of this and or
ease my mind OR let me know what i can do to fix it, hopefully I
dont have to toss them sadly i will but its a bunch.
thanks so much for any input or info you can grace me with.
happy hollidays guys and stay safe.

Pic #1 bottles used to inject #2 lying view of them #3 Bottle after fill before shaking #4 after boiling the mosture out(no more bubbles but as cloudy as a tempur-pedic!)

 

[SpyWizard]

i'd like to know the ba/bb concentration u used..

 

[monte45]

i'd like to know the ba/bb concentration u used..

im sorry i actually purchased this from the most legit ug around and was fine until i transfered from shipping unit into slighty moist bottle my own mistake all i need to know is if this boiled water will or can turn into bacteria ...

 

[ceo]

Can bacteria develop? Yes. It's UG gear that you then transferred in a non-sterile environment into non-sterile vials. Has it been done before with success? Yes.

It's a crap shoot bro. Let us know if you develop an infection. Good luck.

Next time go HG.

 

[monte45]

Can bacteria develop? Yes. It's UG gear that you then transferred in a non-sterile environment into non-sterile vials. Has it been done before with success? Yes.

It's a crap shoot bro. Let us know if you develop an infection. Good luck.

Next time go HG.

haha thanks man brutally honest but any reply is better than none which is what ive been getting my main consear is A; is the boiled sterile water going to ruin the product as far as how it would normally work if it didnt have a small ammount of water

and B; what exactly is the reason for the cloudy look what does the water do to the chemical makeup if any thanks

 

[sony190]

probably from transfering i would hold slightly in boiling water for 2 minutes should be ok then if not dont know however i dont like the way that looks bro why the transfer?

 

[monte45]

probably from transfering i would hold slightly in boiling water for 2 minutes should be ok then if not dont know however i dont like the way that looks bro why the transfer?

thank you very much for your input i actually did the boiling water right before the metal crimp with a needle in the stopper to use the hot air pressure to pull out the condensation...slightly worked less bubbles but when settled still got the cloudy color if not more clouday.. really all im looking for is the explaination of what the water does to the oil and hormones when mixed to make this cloudy color is it extracting the powder out of the oil and mixing with the water? thats really the bottom line info i need but its like the 8th wonder of the world that or im posting in the wrong spots if someone can give me a detailed explanation of exactly what is happaneing to it i can make a well educated descison on if it is safe for use or not.. because i dont care how cloudy it is or how much water is in there they were factory sterile vials re- sterilized in boiling water and when i filled them they wernt propperly dried because im a moron! in a nut shell so im thinking every thing is sterile so whats the harm but the cloudy makeup now is what concerns me some ppl say they shoot cloudy gear with no problems and some say its the ultimate sin. but there is a difference between crased and what happened here where moisture was left in the bottle its such a grey subject because everyone has a diff opinion

 

[monte45]

sorry

 

[ceo]

Why don't you order some sealed sterile vials, some whatman filters, 10cc syringes, 18g needles, and draw it all up and re-filter it back into the sterile sealed vials.

I think our sponsor cheappinz - Cheap Pinz, :: Quality Hardware For All of Your Research Needs - probably has everything you need.