Please Scroll Down to See Forums Below
napsgear
genezapharmateuticals
domestic-supply
puritysourcelabs
UGL OZ
UGFREAK
napsgeargenezapharmateuticals domestic-supplypuritysourcelabsUGL OZUGFREAK

vet chemists please help

the562goodguy

New member
ok so i followed step by step directions off of basskillers site on how to brew prop. but i changed the amounts of ba and bb 3%ba 20%bb. its been about 2wks or so since i made it. i filtered it through a .45 filter twice and both time i inj. i got an infection. so i decided to filter through a .22. and today when i when i pulled out my gear i noticed that the vial has small gray particles floating at the bottom. i have it separated into a few vials and all of them have the same thing. does anyone know what this could be?
the vials i have are clear. could this be an issue?

another question is do i put the rubber stopper on then poke the need through to fill or do i just our the gear into the vial then put the stopper on then crimp?
 
the vials were cleaned with ba to sterilize but not baked in the oven. i didnt think they would need to be. also 2 of the vials were sterile presealed vials.
 
I am no pro but I have always thrown mine in the oven weither its from a sachet or a batch of tren. I transfer into a sterile vile using a sterile surrenge a sterile .45 um whatman and a sterile needle into a sterile presealed vial. Even with all that sterility I still throw my vials that I just filled and labeled into the oven preheated to 250 degrees F for 30 minutes. I take no chances with an infection one of my gym buddies got a staff infection from a insterile vial and he now looks like he has been shot in the tricep with a 44 magnum.
 
First, why did you change the recipe? Like the burn of BA?
Second you dont need a solubulizer and God only knows what it was. DO you? All kinds of nasty shit left over afterward.
Third, when filtering with your syringe filter (always use a 22um pore filter) You were not gentle enough and the 18g needle tore pieces of grey butyl stopper off and into your gear.
Refilter it all into a new sterile vial being gentle enough not to tear the stopper.
You are getting an infection because of A. the byproducts and remaining toxic chemicals left behind after adding the estro sulubulizer.
And B. You only filtered through a 45um pore filter. Those pores are so large I could drive a campervan through them.
Think about all the shit that could have passed through that filter. How clean were you when doing your conversion?
Were you working in your bathroom or worse yet, kitchen? There are more potentially lethal bacterium in your sink than in your toilet. Did you wear gloves and scrub down?
Have you ever done any chemical conversions before? If not, how much research did you do before attempting to produce test prop from a cattle implant? Enough that your confident that your end product will not kill you?
Im not judgin, Im just sayin.
 
hey thanks for all your help and advise. btw i acutally set aside a table, which I cleaned with bleach, and this is where i made my conversions also i did scrub down and did use gloves during the process. i didnt use cattle pellets. i used powder hormone. i did use a .22 syringe filter then a .45 when i transfered it from a 60ml to 10ml vials. how ever i think I baked out the ba or bb which made it crash on me once I've injected. i recently added more ba and bb to one of my vials and I am currently testing it out to see what happens. i am def. gonna check out those links you posted and see what up. oh and btw i want to make a 200mg/ml batch but dont know where to get eo oil. if you have any suggestions or good site please send them my way on here or in a pm. thanks once again. i cant stress how much i've learned from all the good guys on this site.
 
Top Bottom