Test Cyp Cloudy??

[jonny jacked]

I have *********** - testosterone cypionate 250mg/ml

my question is within the last 7 days (just went to do my shot - last shot was 7 days ago).
When i pulled the bottle out today it has turned a very cloudy, almost opeg (sp?) color. also very viscus (sp?) This is compared to how it was a week agon which was very clear, smooth flowing.

I store it at room temp. same place every time.

anyone know how or why this happened? more importantly, is it still good, or should I discard it?

 

[Selfcentor]

You mix any other gear in it from drawing somethign out before drawing out of it with same needle?

 

[jonny jacked]

You mix any other gear in it from drawing somethign out before drawing out of it with same needle?

no, i use an 18 guage pin to draw with from the cyp (and only the cyp).

but, are you saying that if i used the pin from my tren (which i am also running) and then put that same pin into my test - the result would be the cloudy shit?

as a side note, looking at it today it has almost crystalized a bit (best way i can describe it).

what i need to know is - can i still use it?

i would also like to hear from others as to the causes of this???

i thought i heard something about if you heat your gear up it will clear it up? is that true? if yes, how is it done properly?

karma to those that help a bro out!

i dont want to use this stuff and then have to get my arm cut off!!

 

[jumpmaster82]

Ide hav to see it bro

 

[jonny jacked]

Ide hav to see it bro

if i get a chance i will take a pic and post (if I can figure that out!)

Has no one heard of this happening?

 

[big greg 82]

try heating it up n see if that helps, if it doesnt i wouldnt use cloudy gear.

 

[Cryptlord]

It might be the test seperating from the oil?

 

[BOWTECH]

Heat up the vial with a blow dryer on high heat for about 2-3 minutes and shake it up good this should clear it right up. Has worked for alot of people. You may have to do this every one in awhile.

 

[Acela]

boil up some water. let it cool (so its not a "rapid" or "rolling" boil) and then let your multi-use vial sit submerged in the H20 for 1-3 minutes. check it every 30 sec. or so

 

[jonny jacked]

thanks for the info guys.

ACELA - i will try this method, see if it works.

but, does anyone know WHY this happens? what process is occuring?

 

[Illuminati]

thanks for the info guys.

ACELA - i will try this method, see if it works.

but, does anyone know WHY this happens? what process is occuring?

for some reason its not holding. when it crystalizes, it is because the cypionate is falling out of the oil. heating it up will allow it to go back to a nice mixture, but this will most likely just be a temporary thing, and it will fall back out again. best way to heat it up is boil some water in a pot with the vial in it until the crystals go away. (put a needle in the top to relieve the pressure, preventing the top from popping off if its if its not sealed).

no you won't have to get your "arm cut off." no you don't have to discard it.

another option that you have, would be to dilute the concentration down. get yourself a whatman filter (try getpinz.com) get yourself some oil (either grapeseed, soy, or ...) and add the appropriate amount of filtered oil to make the concentration now 200mg/ml. this should be low enough for it to hold. if you need help with the calculations, just post up how many ml's are left, and I can figure it for you

 

[jonny jacked]

well, I did take your advice and heated the test up - and it worked!

I put a coffee mug with about an inch and a half (just high enough so the top of the bottle would not be completely submerged in the water) and heated it to a boil in the micro. then droped the bottle of test in for about a minute. this completely removed the cystalization which had taken place.
I then let it cool and did my shot. everything went perfect - and I still have my arm!!

but, as Illuminati eluded to, this was only a temporary fix, and I will have to repeat the process.