Site injection pin size

[Bobber]

Used 25g 5/8" pin for the delt today and it was like nothing...........waaaaaaaay better than those 22 or 23g inch inch and a halfers I was using before.

 

[DocTodd]

25's are good for almost anything and dont hurt too much.

22's are crazy.

T

 

[ripper2]

i use 25's for everything. no problems at all getting any oil to go through them.

might want to try 1" in the delts though. if you dont' get the oil deep enough you'll get lumpy spots on your delts.

read on one thread a while back about a guy saying they use 5/8" pins for newborns when they give them shots in the shoulders in the hospitals, so 1" shouldn't be a problem for most guys

 

[javaguru]

25g 5/8" or 1" works great for everything unless you're obese.

 

[jb160]

you guys are able to push oil through a 25 gauge? I can barely get it out 22 gauge it takes like 1-2 mins to get all my deca out a 22 gauge in my arm shit am I doin something wrong?

 

[2Thick]

you guys are able to push oil through a 25 gauge? I can barely get it out 22 gauge it takes like 1-2 mins to get all my deca out a 22 gauge in my arm shit am I doin something wrong?

What kind of oil are you using? It should flow like water through the 22g.

 

[goliath.jr]

I use 23g for quads/glute and 25 for everything else...I think I'm gonna start using 25's for everything when I run out of 23's.

 

[jakson]

23G 1" work fine for my deca as well as everything else for that matter...all the way in the delt injection done ine 30 seconds...btw how many cc's r u injecting for the 2 minute injection??

 

[jb160]

dude only 2cc's at a time it is so thick though hell it even takes 4 ever to pull the deca into the pin. I shoot into my arm/shoulder maybe it is just the site.

 

[shoichi]

i use 25's for everything. no problems at all getting any oil to go through them.

might want to try 1" in the delts though. if you dont' get the oil deep enough you'll get lumpy spots on your delts.

You have to watch avoid using the same injection spots, or else your body won't break down the oil. I'm using 5/8 right now, and if I were to do another cycle, would definitely switch up to 1".

On the other post, try heating the amp or rediject up first. You'll find that the oil flows alot better when warm.

 

[jb160]

You have to watch avoid using the same injection spots, or else your body won't break down the oil. I'm using 5/8 right now, and if I were to do another cycle, would definitely switch up to 1".

On the other post, try heating the amp or rediject up first. You'll find that the oil flows alot better when warm.

thanks I caught that in another thread just a minute ago I will 4 sure try that Shit I was going to go up to 20 gauge but I hang freakin pictures on my walls with nails smaller than those damn needles

 

[Jeff_rys]

you guys are able to push oil through a 25 gauge? I can barely get it out 22 gauge it takes like 1-2 mins to get all my deca out a 22 gauge in my arm shit am I doin something wrong?

As 2Thick stated: any oil-roid goes through a 25 g. Any (human grade) water solution goes through a 30 g.

1) The length of the needle is important. Easier with a 1 inch needle then a 1 1/2 inch (who needs that)
2) the size of the syringe is important: The smaller the syringe, the better. So a 5 cc syringe is easy to draw up, more difficult to shoot.

If you can use a 2 cc syringe.

Jeff