QVE-004 Enth 50ml -- Pain reduction by leaps and bounds...

[bunkka]

I'm going to try this today.

I've been thinking though... is there any danger of the rubber stopper melting at that temperature? And should I remove the plastic away from the pin, too, out of fear of it melting?

Just dont wanna f-up my big batch of Test.

Dag... that stuff is literally a pain in the ass, though!

1st week front loaded with 500mgs in each cheek. 2nd week decided to notch the frontloading down to 375mg in each cheek and I'll do the same this week.

Had planned on 2 weeks of frontloading 1000mgs, then on to weekly injections of 500, but 1000mgs absolutely killed me!

I'm hoping by next week when i'm down to 500 the pain will be totally gone with cooking it, though.

Thanks and hope this helps!

 

[barbell265]

no worries Bro'

I'm going to try this today.

I've been thinking though... is there any danger of the rubber stopper melting at that temperature? And should I remove the plastic away from the pin, too, out of fear of it melting?

Just dont wanna f-up my big batch of Test.

Dag... that stuff is literally a pain in the ass, though!

1st week front loaded with 500mgs in each cheek. 2nd week decided to notch the frontloading down to 375mg in each cheek and I'll do the same this week.

Had planned on 2 weeks of frontloading 1000mgs, then on to weekly injections of 500, but 1000mgs absolutely killed me!

I'm hoping by next week when i'm down to 500 the pain will be totally gone with cooking it, though.

Thanks and hope this helps!

Don't worry about melting the stopper or the hub on the pin bunkka. 250 deg for 10 min is not enough to melt either or damage the test. Fina is more susceptable to damage by heating as it has a lower melting point, but the oil "insulates" it , if you will. Just give it 5 min or so to cool outside the oven, leaving the pin in place. This also prevents any unwanted reactions.

 

[Citruscide]

I'm going to try this today.

I've been thinking though... is there any danger of the rubber stopper melting at that temperature? And should I remove the plastic away from the pin, too, out of fear of it melting?

Just dont wanna f-up my big batch of Test.

Dag... that stuff is literally a pain in the ass, though!

1st week front loaded with 500mgs in each cheek. 2nd week decided to notch the frontloading down to 375mg in each cheek and I'll do the same this week.

Had planned on 2 weeks of frontloading 1000mgs, then on to weekly injections of 500, but 1000mgs absolutely killed me!

I'm hoping by next week when i'm down to 500 the pain will be totally gone with cooking it, though.

Thanks and hope this helps!

Just make sure you put the dart (WITHOUT the syringe) in the top of the stopper... make sure the dart isn't in contact with the oil.. so the oil can't ooze out.

My friend *wink* had the bottle in there for 25 minutes x 3 with 15 minute cooling off periods... it worked wonders for him *wink*

C-ditty

 

[bunkka]

Thanks! Wink!

I wonder if this might be MY friend. Wink!

HEEEEEE (My friend) has a small penis and wonders if those penis pumps work. Wink!

 

[AAP]

I'd like to hear why.
If you're saying it'll "crash" in the muscle, add some benzyl benzoate. This is lipid soluble. Or, you can add more sterile oil to dilute. Or both.

I wish I could find that posting as well. But these guys have written and told us why you should not take out the BA in a compound.

Karma to the one who finds it... I want to show someone else this too.

 

[Fonz]

I'm going to try this today.

I've been thinking though... is there any danger of the rubber stopper melting at that temperature? And should I remove the plastic away from the pin, too, out of fear of it melting?

Just dont wanna f-up my big batch of Test.

Dag... that stuff is literally a pain in the ass, though!

1st week front loaded with 500mgs in each cheek. 2nd week decided to notch the frontloading down to 375mg in each cheek and I'll do the same this week.

Had planned on 2 weeks of frontloading 1000mgs, then on to weekly injections of 500, but 1000mgs absolutely killed me!

I'm hoping by next week when i'm down to 500 the pain will be totally gone with cooking it, though.

Thanks and hope this helps!

I can't wait till you post about the size of your abscess.

You know what ther BA does?

Its a STERILIZING agent for the solution.

Kills the bacteria. And acts a sterilizing agent once you inject the AAS intra-muscularly.

And even if you cook the non-BA product(Form of pasteurization btw), some bacteria WILL NOT be killed b/c you cannot heat the solution to a high enough temperature or you destroy the AAS.

But go ahead and try it. I warned you, and so did others.

But I guess you'll learn the hard way.

Fonz

 

[bunkka]

This, I learn as I'm on my last 25 period in the oven.

Oh well... I'll risk and absess.

 

[Citruscide]

Good dig Fonz... just FYI (for everyone else) Boiling point for BA is 398F... the hormones in your test break down around 400-450F... so it's really pushing it... you don't want to fry the good shit...

C-ditty

 

[goheavy63]

Bump. Which process is Fonz talking about??? The baking or the Bacteriostatic water method. Or both!!!

 

[Citruscide]

Fonz is talking about the adding water method...

Baking it in the oven could not have this affect, as it will not effect the BA content of the mixture.

C-ditty