problems injecting winny

[kenleo]

im using a 23 gauge 11/2 inch to inject. the first injection went smooth in the quad, but the last three the gear wouldn't go thru the needle, the plunger wouldn't budge no matter how hard i would press on it. i have tried in my glutes and quads with no luck. i had no choice than to drink it. what can i be doing wrong? please help. it is ttokkyo winny.

 

[ZeroCool]

im using a 23 gauge 11/2 inch to inject. the first injection went smooth in the quad, but the last three the gear wouldn't go thru the needle, the plunger wouldn't budge no matter how hard i would press on it. i have tried in my glutes and quads with no luck. i had no choice than to drink it. what can i be doing wrong? please help. it is ttokkyo winny.

Is it the 50mg Winny or the 100mg winny by Ttokkyo?

 

[kenleo]

100mg winny. trying to inject 50mg ed.

 

[Enigmaxxx7]

There are a couple of things that I do that help.

First of all, be completely ready to inject. Don't fool around and waste time.
Shake the bottle good.
Inject air into the bottle and then draw out winny.
Then draw up a very small amount of some oil base like test or eq.
Just enough to fill the pin itself. This will lube the pin.
Then inject.

You may want to also consider 100mg EOD if it is too much of a pain. I rather shoot winny Every day though if it is possible.

 

[kenleo]

bump!

 

[ZeroCool]

I have the 50mg Ttokkyo winny and I have trouble injecting it as well. I have heard time and time again that injecting te 100mg winny is very hard to do. That is the reason I decided to get the 50mg winny instead. Before I inject I shake the bottle up very good. Try doing this it might help............

Before you inject the needle into the bottle of winny pull the plunger back as far as it goes with nothing in the syringe. Now the syringe is filled with nothing but air.....Put the pin into the bottle of Winny and push the air that was in the pin into the bottle. Basically you are filling the bottle with air so the gear inside the bottle has pressure buildup and will force the winny into the pin a little easier. Then try to fill the pin with you gear as you normally would..............Then go on with your injections as you normally would. This might help. Good Luck.

 

[azdave]

I've had similar problems injecting prop when the plunger refused to budge, and usually changing the needle again on the same syringe worked.

 

[kenleo]

i do change the needle. i use a 18 gauge to draw an 23 11/2 to inject.

 

[ken69dahl]

If you are taking anything else with your winny try adding in an oil based product after you load the winny. Shake it up, it wont mix but will make it go through allot easier. Also draw up your gear with a seperate pin. I always draw with a 19g and shoot with 25g.

 

[azdave]

I draw and poke with seperate needles also. I should of been more specific.

When I can't get the plunger to move, I've pulled the needle out my thigh, pull some air back into the syringe, remove the needle, attached a third needle, then squeeze the air and some gear back out of the syringe and new needle (the third one), and then try shooting again.

 

[ZeroCool]

If you are taking anything else with your winny try adding in an oil based product after you load the winny. Shake it up, it wont mix but will make it go through allot easier. Also draw up your gear with a seperate pin. I always draw with a 19g and shoot with 25g.

I definitly would not take this advice. Mixing an oil and a water based in the same pin is bad news. Next time you inject if the winny gets stuck in the pin while in the injection process then take it completly out unscrew the pin off the barrel of the syringe get more air into the pin so it forces the gear through te needle. Unfortunatly sometimes the crystals are to big to get through the needle but the results are worth it.

 

[Enigmaxxx7]

I definitly would not take this advice. Mixing an oil and a water based in the same pin is bad news.

ummmm. why?

 

[kenleo]

bump

 

[FLmuscles]

I had this problem last cycle with the Ttokky 100-mg WInny. It would never seem to dissolve, even thought I shook the bottle really good, I'd get little blobs of WInny floating into the syringe. FInally, I couldn't get anything out of the vial, so I took some pliers and tore off the stopper to the vial, to find it all clogged up with a big clump of WInny goo. Who knows how much I was really getting with each shot.

 

[Surgical]

I use a little longer needle, maybe 1". I think what happens is that the winny suspension has no where else to go, that's why the plunger stops. I just back the needle out, maybe a millimeter or two, and try again. It usually goes in easy after that. It's not like an oil base that can be more easily absorbed by the muscle cells.

 

[ZeroCool]

ummmm. why?

Because if the crystals in the winny clog the pin then you waste 2 types of gear instead of just a 1/2 cc. He said he has the 100mg winny so 1/2 of cc would be 50mg. Sometimes the pin just gets clogged............Believe me I know it sucks I am doing ed injections because the winny never mixes right if the is oil in the barrel. It just happened to me a few hours ago.

 

[daveyboy]

I used the 100mg TT Winny this past summer & I know exactly what you're talking about. It got to be such a hassle trying to shoot it without clogging that I just took the easy way out & drank it each time. I had to forget about doing site injections with the stuff but it still worked pretty good.

 

[liftsiron]

Winny is just a fucking pain in the ass to inject. The last time that I injected winny I mixed it with an injectable B-vitamin solution, this helped. Now when I get injectable winny at a good price I just drink it and seem to get the same results without any hassle. Mixing winny with an oil based steroid does help somewhat with the injection.

 

[Enigmaxxx7]

Because if the crystals in the winny clog the pin then you waste 2 types of gear instead of just a 1/2 cc. He said he has the 100mg winny so 1/2 of cc would be 50mg. Sometimes the pin just gets clogged............Believe me I know it sucks I am doing ed injections because the winny never mixes right if the is oil in the barrel. It just happened to me a few hours ago.

True, oil and water don't mix in the barrel. I'm not talking about mixing Winstrol and say EQ to save on injections. I never pull in enough oil to pull into the barrel. Just enough to lube the pin which is only a few drops.

But hey, this is age old problem and I think he has every possible remedy so far. If he doesn't like any of these ideas, DRINK IT.