Please Scroll Down to See Forums Below
primo.powder
- Thread starter bigtravis
- Start date
cornfish
New member
There are recipe's on the forums.
You can basically run 1-5% BA and BB up to 20% if you like. There are allot of misconceptions about BB causing pain but there are guys that have taken a full CC of BB stand alone and had no pain whatsoever. With primo it's just best to stick with 100mg/ml though and put up with the extra sticks. It's so much more painless, but just use the powder calc and you can tell where you will end up. Check the chem forums
You can basically run 1-5% BA and BB up to 20% if you like. There are allot of misconceptions about BB causing pain but there are guys that have taken a full CC of BB stand alone and had no pain whatsoever. With primo it's just best to stick with 100mg/ml though and put up with the extra sticks. It's so much more painless, but just use the powder calc and you can tell where you will end up. Check the chem forums
I thought for sure I had a recipe on disk, but couldn't find it anywhere. (got everything else) So I went on a search and found that the guys over at beyondmass.com, including Harvey Balboner, the conversion guru, say to convert primo the same way you would test prop. LMK if you need that recipe.
Here's a link.
http://www.beyondmass.com/forums/showthread.php?threadid=7384&highlight=primo+powder
Here's a link.
http://www.beyondmass.com/forums/showthread.php?threadid=7384&highlight=primo+powder
Güclü_oglan
New member
1g = 10ml x 100mg (10ml of 100mg per ml)bigtravis said:
1. It's real simple bro, take a clean glassbeaker where you can see the volume in ML or CC
2. Put 10g of powder in there
3. take a dash of bb and ba and pour it on the powder (i can't tell the ammounts of BB and BA for primo email radar's secure mail i think he has made primo)
5. take a saucepan and boil up water in it, once water starts boiling take it off the heat
6. Lower the beaker of the mixture into the hot water (the water should NOT be boiling or you might crack the glass if you do sudden changes in temperatures) make sure no water gets in the beaker just make sure it's heating the mixture
7. now you will see the solution melting down slowly, keep ut melting until it has all molten and swirl around the mixture a little bit, keep it heated until it has all gone into a nice solution (even the foam should dissolve)
8. now add the oil until you've got 100ml of total mixture (the heated solution+oil should be 100ml if you're doing 10,000mg @ 100mg/ml)
9. take a syringe and attach a needle (10cc and plus is recommended because filtering with smaller syringes will piss you off) now fill the syringe and attack a filter and a FRESH needle (don't reuse the unsterile one for bringing the solution into the syringe)
10. Now filter it into a sterile vial and get pissed off and start thinking about killing yourself etc(like i do everytime it's time for the fucking filtering) when you see that 100ml of solution is gonna be put in that vial. All you will see is that the little fuckers are only dripping at a damn small pace
11. If you make it through the filtering you will have some sterile shit in the vial. Now put another fresh needle into the rubber stopper of the vial to vent the air-pressure and put it in a water bath (look at step 5 on how to heat the water) let it sit for half an hour.
Many people say the last part is unecassary and won't do shit but i dunno if you feel like it do it, else you don't have to
good luck bro, i would hire someone for the filtering tough....
Güclü_oglan said:1g = 10ml x 100mg (10ml of 100mg per ml)
1. It's real simple bro, take a clean glassbeaker where you can see the volume in ML or CC
2. Put 10g of powder in there
3. take a dash of bb and ba and pour it on the powder (i can't tell the ammounts of BB and BA for primo email radar's secure mail i think he has made primo)
5. take a saucepan and boil up water in it, once water starts boiling take it off the heat
6. Lower the beaker of the mixture into the hot water (the water should NOT be boiling or you might crack the glass if you do sudden changes in temperatures) make sure no water gets in the beaker just make sure it's heating the mixture
7. now you will see the solution melting down slowly, keep ut melting until it has all molten and swirl around the mixture a little bit, keep it heated until it has all gone into a nice solution (even the foam should dissolve)
8. now add the oil until you've got 100ml of total mixture (the heated solution+oil should be 100ml if you're doing 10,000mg @ 100mg/ml)
9. take a syringe and attach a needle (10cc and plus is recommended because filtering with smaller syringes will piss you off) now fill the syringe and attack a filter and a FRESH needle (don't reuse the unsterile one for bringing the solution into the syringe)
10. Now filter it into a sterile vial and get pissed off and start thinking about killing yourself etc(like i do everytime it's time for the fucking filtering) when you see that 100ml of solution is gonna be put in that vial. All you will see is that the little fuckers are only dripping at a damn small pace
11. If you make it through the filtering you will have some sterile shit in the vial. Now put another fresh needle into the rubber stopper of the vial to vent the air-pressure and put it in a water bath (look at step 5 on how to heat the water) let it sit for half an hour.
Many people say the last part is unecassary and won't do shit but i dunno if you feel like it do it, else you don't have to
good luck bro, i would hire someone for the filtering tough....
Great post. The filtering goes a lot easier if you heat up the oil and use a thin oil like grapeseed.
thanks bigtime yall this helps out like you would not believe!Güclü_oglan
New member
yea np i'm glad if it helped, but ask around for good primo ammounts, if you're brewing it yourself never go above 1.5% of BA because it's not needed as long as you wipe the rubber stopper frequently with BA or other good stuff against possible bacteria, BB doesn't hurt
Similar threads
