Pre Heating Test Prop in the Syringe???

[Prizz]

Ok, we talked about this in a past thread, and no one has commented, so I decided to make my own thread..... In one of the MILLIONS of Test Prop Hurts Threads, someone posted on how they heat their Prop in the syringe before shooting, to burn off some of the BA, and make it less painful..... However, I forget who it was, and how they did it.... I think the person said 20mins in the oven, at 150 degrees, take out, let cool for 3 mins, then shoot it..... Something like that..... Anyone know anything about this? It has me very curious, especially since I have a Prop/Tren cycle coming up.....

rizz

 

[Jon79]

prizz no one is answering.....what brand is it? is it unbearable? i guess it would just evaporate out of the needle?

 

[bca21]

well why not dilute it a lil.1cc test prop 1cc oil

 

[fcfmuaythai]

why not just use painless prop, it is out there if you look in the right places

 

[bigcountry61]

why not just use painless prop, it is out there if you look in the right places

 

[drrman]

well...i would NOT put my syringe in a hot oven or anything else that would get it to 150 degrees......the pain is not from the initial injection, its from the depot or the prop sitting in the muscle

there ARE painless props and i have taken and made them......but i would not heat my plastic syringe any more than what a hot faucet will do or what a hairdryer will do

 

[lanky]

well...i would NOT put my syringe in a hot oven or anything else that would get it to 150 degrees......the pain is not from the initial injection, its from the depot or the prop sitting in the muscle

there ARE painless props and i have taken and made them......but i would not heat my plastic syringe any more than what a hot faucet will do or what a hairdryer will do

well put

 

[ALIN]

Ok, we talked about this in a past thread, and no one has commented, so I decided to make my own thread..... In one of the MILLIONS of Test Prop Hurts Threads, someone posted on how they heat their Prop in the syringe before shooting, to burn off some of the BA, and make it less painful..... However, I forget who it was, and how they did it.... I think the person said 20mins in the oven, at 150 degrees, take out, let cool for 3 mins, then shoot it..... Something like that..... Anyone know anything about this? It has me very curious, especially since I have a Prop/Tren cycle coming up.....

rizz

you could run the syringe thru some hot water to see if that helps. its the prop ester that causes the pain though.

 

[theprofessor]

why heat the syringe??? seems easier to just bake the vial/amp at low temp and then draw...
...but painless prop is realy the way to go... that and the pain does ease up a lot about 2-3 weeks in...

 

[Neo22]

why not just use painless prop, it is out there if you look in the right places

maybe bc all painless is 50mg per ml. Meaning you would need 3cc for 150 per shot?

 

[Jon79]

maybe bc all painless is 50mg per ml. Meaning you would need 3cc for 150 per shot?

no offense
maybe it's because you don't know what the fuck you are talking about...
there is 100mg/ml painless prop....jesus gave it to me i know it is legit

 

[H_T_]

ya know, the whole dilluting thing is ok. i mixed in some enth with the prop and it didn't hurt nearly as bad.

 

[Andy13]

IMO, "heating to reduce pain from BA" doesn't actually "boil off" the BA. There have been reports that heating gear reduces the pain.. This has been attrubuted to "loss of BA through evaporation/distillation." I feel this is absurd. One cannot "boil" the BA out of solution.

Instead, what I think happens is a transesterification.. Meaning, you have your AAS (an alcohol esterified) and another alcohol (BA) and tri-acyl glycerides (esters). When heated, the steroid becomes loses battle with BA (another alcohol) and becomes a free steroid (no ester).


It's a bad, baaaaad.. ideal to bake gear

 

[drrman]

maybe bc all painless is 50mg per ml. Meaning you would need 3cc for 150 per shot?

WHAT??? i've made painless at OVER 100mg/ml.......where are you getting your information???

 

[Prizz]

I was just posting an idea I had heard from another poster, and thought it was interesting...... I was just seeing what you guys thought about it..... I don't plan on baking my gear after this thread..... I know there are painless Prop brands out there, but you gotta use what you got ya know? I'm not gonna go buy another batch of Prop cause I want painless.... I'll take the pain instead, it's not that bad anyway....

rizz

 

[theprofessor]

I'll take the pain instead, it's not that bad anyway....

oh fuck yes
i barely notice any pain by 3rd week...