i've got some HCG coming (i know check's in the mail same shit) but have similar ?'s...where do you inject HCG, is it intramuscular in the ass like other AAS or subq like slin/hgh ?jh23 said:Try drawing up with a standard size syringe and pin and then pull the plunger completely out of the back of the insulin syringe and squirt the HCG in equal amounts into each insulin syringe. You of course will have to preload them, just make sure to store them in the fridge until you are ready to use them.
Intramuscular (glutes, delts, thigh, etc.) or SubQ...both are fine. I prefer glutes...and you don't need to get an 1.5" 22g either as it is not necessary to inject as deep as AAS. A 1" (or even 5/8) with 23 or 25 gauge will do!LVTitan said:i've got some HCG coming (i know check's in the mail same shit) but have similar ?'s...where do you inject HCG, is it intramuscular in the ass like other AAS or subq like slin/hgh ?
help4john said:Just a side note....are you planning on storing the HCG with the solvent mix in the frig? If so, it won't be any good after a couple of days anyways. If you are mixing with bacteriostatic water:
1) Draw 1cc of BSH2O into normal syringe (22,23, or 25 gauge)
2) Open HCG powder amp
3) Inject the 1cc of BSH2O into amp (mixing the powder and liquid)
4) Pull contents of amp into syringe (1cc, still 5000IU's)
5) Put the 1cc BSH2O and HCG combination into a sterile vial
6) Draw an additional 4cc of BSH2O into the syringe (or 2X at 2cc's)
7) Inject this into the vial
8) You now have 5cc in the vial
9) Inject 1/2cc ..... this will give you 500IU of HCG
10) Refrigerate for next use
Hope this helps! Good luck!
1) The solvent deteriorates the life of the powder. It will only last about a day before losing strength. Just toss the solvent.jcam222 said:Nice info ....exactly what I was looking for . Couple questions though.
1) Why cant you use the original solvent and just add the additional BW?
2) Who is the best source of presealed sterial vials to use for this?
K for any advice.
You can cut the BSH2O in half so you will only need to inject 1/2cc. Less water could be used in the mix.....but it's so much easier IM.Anakin said:One more thing, would you be able to inject the new solution (with BSH2O) sub-q?
And how much can you inject sub-q, cause 1ml sounds like a lot for that.
jh23 said:Try drawing up with a standard size syringe and pin and then pull the plunger completely out of the back of the insulin syringe and squirt the HCG in equal amounts into each insulin syringe. You of course will have to preload them, just make sure to store them in the fridge until you are ready to use them.
help4john said:Just a side note....are you planning on storing the HCG with the solvent mix in the frig? If so, it won't be any good after a couple of days anyways. If you are mixing with bacteriostatic water:
1) Draw 1cc of BSH2O into normal syringe (22,23, or 25 gauge)
2) Open HCG powder amp
3) Inject the 1cc of BSH2O into amp (mixing the powder and liquid)
4) Pull contents of amp into syringe (1cc, still 5000IU's)
5) Put the 1cc BSH2O and HCG combination into a sterile vial
6) Draw an additional 4cc of BSH2O into the syringe (or 2X at 2cc's)
7) Inject this into the vial
8) You now have 5cc in the vial
9) Inject 1/2cc ..... this will give you 500IU of HCG
10) Refrigerate for next use
Hope this helps! Good luck!
This page contains mature content. By continuing, you confirm you are over 18 and agree to our TOS and User Agreement.
Please Scroll Down to See Forums Below 














