Need to retool some gear HELP!!

[taoiron]

Need to retool some gear HELP!!


OK…. Need a bit of help from you UG lab bros…. I feel it is necessary for my safety to retool the ASSLOAD of gear I received!!! Is this process antiquate to insure I have sterile gear??

1) Draw the product out of the vial.

2) Inject the product into a new sterile presealed vial thru a whatmans filter.

3) Leave the needle in the vial.

4) Bake @ ______ for ______min
(Please fill in the blanks for me).

Remove needle after product cools and store.

Karma for the help...

Tao

 

[Para_Shoot]

I don't know why you would need to sterilize anything in your chemestry experiment here. Are you drawing your oil, BB and BA out of new glass vials? Wouldn't the contents of these new vials be sterile already? Also, if you put your final product into a brand new, sterile vial, why would you need to re-sterilize it? I only ask you this cause when I made my treasure chest full of stuff, I drew my oil, BA and BB out of brand new vials, then I put the final solution into brand new sealed sterile vials. I didn't bake anything. I have been using all my stuff for over a month now and no side effects.

 

[taoiron]

I don't know why you would need to sterilize anything in your chemestry experiment here. Are you drawing your oil, BB and BA out of new glass vials? Wouldn't the contents of these new vials be sterile already? Also, if you put your final product into a brand new, sterile vial, why would you need to re-sterilize it? I only ask you this cause when I made my treasure chest full of stuff, I drew my oil, BA and BB out of brand new vials, then I put the final solution into brand new sealed sterile vials. I didn't bake anything. I have been using all my stuff for over a month now and no side effects.

I used a UG lab for the first time and I ordered everything for my next 4 cycles…

Problem is I see a couple black specs in a few of the vials and want to remove them…
I can’t replace it so I just want to take any precautions that I can to insure I don’t put crap into my body that I does not need to be there.

Yes…. I should push back on the lab…. But that was a mess…. I think I will make my own next year!! I have a couple of friends that are on his gear and they are staying healthy however some of their gear has the same issue..

So….. Filter it and put it into a new vial??? Add some BA????

Help a Nuggar out!!

Tao

 

[Para_Shoot]

I used a UG lab for the first time and I ordered everything for my next 4 cycles…

Problem is I see a couple black specs in a few of the vials and want to remove them…
I can’t replace it so I just want to take any precautions that I can to insure I don’t put crap into my body that I does not need to be there.

Yes…. I should push back on the lab…. But that was a mess…. I think I will make my own next year!! I have a couple of friends that are on his gear and they are staying healthy however some of their gear has the same issue..

So….. Filter it and put it into a new vial??? Add some BA????

Help a Nuggar out!!

Tao

Yes, I would filter it and put it into a new, sterile vial. I think the only reason you would want to add more BA is if the juice is crystalizing or you can see the powder particles still in there. Too much extra BA makes for a painful shot. Making your own gear is definitly the most cost effective way to go. Also, you can order ANY steroid in powder form instead of searching for already made stuff. Everyone who has an interest in this should quickly become a home chemist!

 

[anal itch]

Just take the stopper off the original vials and draw them up with an 18g pin. Filter them with a .20 Whatman (very slow process) into a new, sealed sterile vial. Be sure to use the smallest gauge pin you have for venting on the new vial. Sticking two 18g pins in the rubber stopper will destroy it.

By the way, don't use a syringe larger then 10cc when filtering. I used a 20cc and had to use so much pressure just to get it through the Whatman that I ended up breaking off the ears on the end of the syringe. I switched to a 10cc and it was much easier!

 

[anal itch]

Bake at 155-175 for 20 minutes. Do this three times and let the product completely cool before baking each time.

Also, leave the venting needle in the stopper while baking and cooling. I like a 27g for this. I also like to completely wrap the stopper with some aluminum foil to deflect the radiant heat away from the rubber.