Please Scroll Down to See Forums Below
napsgear
genezapharmateuticals
domestic-supply
puritysourcelabs
UGL OZ
UGFREAK
napsgeargenezapharmateuticals domestic-supplypuritysourcelabsUGL OZUGFREAK

My first GH injection - please help!

jdevlin1985

New member
Hello guys! RE to the post i posted last week '4iu of HGH for 5 month' I took my first injection this morning. First of all I went to snap of the top of the water vial and the top smashed to pieces (Luckly the water was ok) - Did I do something wrong? Is GH water vials meant to be opened differently to say a winny vial?

Also I pulverised the GH solution with the water by mistake which I know should be avoided however due to the trapped air in the syringe it just flew in. This shouldnt cause a prob should it as i know how delicate the solution is?

I also withdrew 2 iu/11 (ml) (going to taper up to 4iu)....it may be just me but it did not look like even enough plus i couldnt control when injecting - it just shot in (i am going for the bottom right ab region) Inserting into the pocket not the fold is the right way isnt it?


Did any of you guys experience any of thyese probs with your first injection...?

Any advise and feedback is much appreciated

Jay :chomp: It is Jintropin by the way guys
 
Last edited:
If the solution foamed when you mixed it, or if it looks a little cloudy (i.e. like seawater) now, then it's probably bad.

Also... 11 ml's to get 2 IU's? Am I misreading something? It should be about a 0.5 ml (or less) injection, depending on the concentration of the solution.

As far as the shot itself... yes, pick a little fatty place along your abdomen or midsection, pinch the skin, stick and shoot. Just don't hit 1) Muscle or 2) A vein.
 
LoL bro I dont know if anything else could have went wrong there.Insert your mixing pin on the side of the stoper so it hits the curve in the glass at mouth of the vial and when the sucktion pulls it in it wont hit the gh waffer directly.Jinos are 1ml per 10ius so if you shot a full slin pin marked to the 10 you would get 10 ius of gh in.Also do not use the water that comes with the gh as it only stays good for like 24 hours and your not gona use the 10ius that fast by waht you have outlined.Go to your pharmacy or order from online some Bacteristic water.Hope I spelled that right but its close enough.Anyhow good luck bro if you follow this advise you will be goldnen also dont ever shake the gh bottle just swirl it till the powder dilutes in the water.Good luck and hit me with some K for all this typing you just made me do.
 
Gymratforlife said:
LoL bro I dont know if anything else could have went wrong there.Insert your mixing pin on the side of the stoper so it hits the curve in the glass at mouth of the vial and when the sucktion pulls it in it wont hit the gh waffer directly.Jinos are 1ml per 10ius so if you shot a full slin pin marked to the 10 you would get 10 ius of gh in.Also do not use the water that comes with the gh as it only stays good for like 24 hours and your not gona use the 10ius that fast by waht you have outlined.Go to your pharmacy or order from online some Bacteristic water.Hope I spelled that right but its close enough.Anyhow good luck bro if you follow this advise you will be goldnen also dont ever shake the gh bottle just swirl it till the powder dilutes in the water.Good luck and hit me with some K for all this typing you just made me do.

LOL yeh tell me about it Gymratforlife, what else could go wrong :worried: . Thanks guys (and especially 'GYMRATFORLIFE') excellent feedback and advise.

Sorry I think I was meant to put 0.11ml which is 2iu correct? Ok I will take your advise and get some Bacteristic water - Do they come in ready to use vials :rolleyes: if not how much water will i need in each 10iu?

Thanks guys

P.S big up your location description Gymratforlife ;)
 
You will need 1ml to equal the 10ius in the gh vial.This will give you a nice easy way to measure.For example if you use the slin pin up to the 20mark it will=2ius if you use the full slin pin wich is 1 ml you will get 10 ius.each tenth on the slin pin will give you one iu.So add 1 full slin pin or 1 ml to every 10 iu bottle.NOW HAND OVER THE GREEN K DARN IT.
 
Gymratforlife said:
You will need 1ml to equal the 10ius in the gh vial.This will give you a nice easy way to measure.For example if you use the slin pin up to the 20mark it will=2ius if you use the full slin pin wich is 1 ml you will get 10 ius.each tenth on the slin pin will give you one iu.So add 1 full slin pin or 1 ml to every 10 iu bottle.NOW HAND OVER THE GREEN K DARN IT.

Cheers gymratforlife! Not being funny though fella how do i give out the green karma?

You have earnt it :chomp:

:evil:
 
Last edited:
not to be a dick but why the hell are you on here asking questions like this? If you have the sense to go buy a kit shouldn't you be 100% clear on how to use it?

It is like someone who never rode a motorcyle before going out and buyign a GSX-R 1000...Then asking his buddy how to ride it...Sometimes this board just asks the dumbest questions...good luck man
 
2sick said:
not to be a dick but why the hell are you on here asking questions like this? If you have the sense to go buy a kit shouldn't you be 100% clear on how to use it?

It is like someone who never rode a motorcyle before going out and buyign a GSX-R 1000...Then asking his buddy how to ride it...Sometimes this board just asks the dumbest questions...good luck man
That answer is not helping him any bro.If you think that way its better to keep it to yourself,why bother offending others? :rolleyes:
 
Top Bottom