Microwaving Gear- Can it damage It?

[TrueCowboy]

Does anyone have any evidence that an injectable composed of 100mg test prop & 75mg trenbolone acetate per ml could be damaged by microwaving to ~120F? It is easy and convenient to place a loaded syringe (minus the needle) upright (I place it upside down in a drinking glass to avoid running out the syringe tip) to warm for ~30 seconds before injecting.

The only thing I am unsure of is whether or not the microwaves could in any way damage the test or fina (under 150F).

Comments anyone?

 

[DangerousGrounds]

no not at, 120 degrees or below no damage

 

[Frackal]

I sure as hell wouldnt risk it...

 

[Imnotdutch]

Why are you putting it in a microwave?

 

[Latamier]

Why are you putting it in a microwave?

Thats what I'd like to know as well.

 

[TraxZBT]

Why are you putting it in a microwave?

heat up the oil so it's thinner. Less pain and smoother injection.

 

[DangerousGrounds]

it is fine to put vial or amp or capped syringe in. A better metod might be heat water up and let vial, amp, ect warm up a bit before

 

[Imnotdutch]

heat up the oil so it's thinner. Less pain and smoother injection.

Oh I see.........I'd just use DangerousGrounds idea if that were an issue wuth me.

 

[benchpressr23]

I woul not put it in the microwave. Stove maybe, but not the microwave

 

[TrueCowboy]

Reason for Microwaving: Heating the injection to reduce pain; faster and more convenient than warm water

ED prop injections could be quite irritating over extended time

Microwaving is simply fast and convenient way of heating it. I place the syringe (minus needle) upright (using a small drinking glass as a holder) and microwave for 30 seconds. The first two weeks I didn't do this. I had lumps at injection sites 1-2 days after each injection. The next two weeks I microwaved as a test. It significantly reduces the irritation at injection sites. The question is whether the microwaves could damage the Prop or Tren?

Any science gurus have any ideas one way or the other.

If it is in fact an OK method. This is a GREAT combo.

 

[marky]

the assumption in all the posts is...

that we are talking about vet gear. My experience using strict inj protocol has been no infection or any other problems over 17 years. And Ive use the same stuff anyone on the boards are talking about. I have used Terumo the whole time.Never a different brand even with slin. Theres benzyl acohol in every oil based gear. Enough to keep the gear safe. Now if the integredy of the bottle might be in question like the cap turns easily or there is a good dent on the side. Ive tested the seal on vials by blowing them up with air and then if the needle plunger scoots back on its own, i know the sea is good. IMO Injection technique is the root of all problems with legit gear. Underground lab stuff Ive NEVER touched. My .02c

 

[DangerousGrounds]

Reason for Microwaving: Heating the injection to reduce pain; faster and more convenient than warm water

ED prop injections could be quite irritating over extended time

Microwaving is simply fast and convenient way of heating it. I place the syringe (minus needle) upright (using a small drinking glass as a holder) and microwave for 30 seconds. The first two weeks I didn't do this. I had lumps at injection sites 1-2 days after each injection. The next two weeks I microwaved as a test. It significantly reduces the irritation at injection sites. The question is whether the microwaves could damage the Prop or Tren?

Any science gurus have any ideas one way or the other.

If it is in fact an OK method. This is a GREAT combo.

I like 25g, I usually put my object of choice in a coffee cup when I have coffee temp water in it, let it sit for 30 seconds or whatever.

I swear it helps with pain fever and swelling later for on sites. I heat "don't flame or laugh" on a clean sterile spoon lowest heat until oil on edges just starts to form bubbles, no hurry (mins)

I let cool 5 mins and use 18ga draw 2 1/2 cc's (change with 23ga or 25ga) and push out 1/2 cc air,ect. let drop lube pin.

Took away fevers, lumps in bi's, tri's every time for me used about every time aas with this method mixed ect. and don't flame or call junkie please its not injecting IV.
just a tip I use my method and recommended by ip but a lot less heat used (slower) by my method

 

[TrueCowboy]

the assumption in all the posts is...
that we are talking about vet gear.

Yep, it's underground vet gear alright.... _ made it.

 

[Latamier]

heat up the oil so it's thinner. Less pain and smoother injection.

You big PUSS! Just suck it up and inject it like a man.LOL

 

[trial0r]

i wouldnt microwave the plastic in the syringe let alone the juice.

 

[justwannagetsum]

use the hot water method... microwave = bad, em kay

 

[Mikeygun]

yeah but when your injecting like 3 different types of roids 3 days a week what are you gonna do?.....heat all 3 vials everytime you need to shoot?....its starting to be a pain in the ass doing this, im also looking for an alternative way of doing this. what if i put the juice in the needle and put the needle between a heating pad for about 10 minutes, would that work?