inject fina ???

[ItalianSta]

I have the 4go kit and added 2 packs of fina to the magic solution , 50 minutes later I added the oil and all the pellets are still intact . Are they suppose to dissolve ? I don't believe so but I'm not sure . And how long do I let it sit with the oil mixed in before I filter it . I have been on Mr h web page and folloowed his instruction .

 

[TxLonghorn]

Well, I personally don't add the oil until the pellets have dissolved in the magic solution.

Try heating it up though. Get a pot with some water, put it on some heat, not too high, and hold the vial in there and swirl it occasionally.

 

[Zyglamail]

Just a note, if you have an A kit, things have changed slightly since. You dont need to prefilter, just avoud the gunk in the bottom when drawing out with needle to sterile filter, there is little or no tren in the gunk anyways.

As for your question, yes the pellets should have been dissolved prior to adding oil. You can crush them up after adding them to magic solution with a glass rod or heat slightly by placing vial in boiled water that has been removed from stove. Or, simply let it sit until it does dissolve. Personally I let mine sit overnight.

P.S. I hope you drew some oil out for flushing the sterile filter before adding the oil to magic solution.

 

[needleboy]

The instructions I have did not say it was necessary, but I figured they needed to be full dissolved- did the boiling water trick- worked like a charm!!!

BTW- am literally doing it right now.

My question is I added the oil, swirled it and am letting it settle. How long should I wait to filter???

It seems to be separating out into 3 layers. the bottom is kind of white, then a layer that is brownish rust, then a layer that is is yellowish.

Am I correct that the bottom(the white part) is glue/fillers but the other two are the tren????

Do I want to transfer the yellow and the rust brown, but avoid the white??

BTW- am using a 2gO kit- not that it makes a difference.
Also should this be refrigerated now?? How about after filtering???

 

[Zyglamail]

After the oil is added, swirl and let it settle, Boil some water on the stove, then remove pan from water and place vial in water for ohhh, 7-10 minutes. This will further seperate and turn the gunk into sticky gung that mainly glings to the bottom. Pull from water and let settle again. Once settled, place back in boiled water to just warm it up a touch so that it flows through the filter better. When it is a tad warm, go ahead and draw someout and steril filter avoiding gunk on the bottom. As you get lower, gently tip vial at an angle and draw from the outside edge, getting as much liquid as you can. The gunk is nothing but trouble and contains little or no tren.

 

[anabolic24/7]

Try not to suck up the dark brown 'ooze', Animal said it is water and not a problem, but the filter will let the 'ooze' go through. It makes the finished product unsightly.

 

[needleboy]

Do I need to refrigerate from this point on????

 

[anabolic24/7]

nope

 

[Zyglamail]

No refrigeration needed. The oil has preservative properties, just keep in a cool dark place.

 

[ItalianSta]

Thanks for all the replys , I did put the bottle in some hot water and waited until the pellets disolved completely . Then I filtered it thru a coffee filter and I have nice golden oil with a bunch of shit in the first bottle . I don't think I'm gonna try and squeeze the thick shit . Now do I bake in oven or not ?

 

[Zyglamail]

Prefiltering with a coffee filter isnt necessary if your carefull when drawing solution prior to sterile filtering, but since ya did it, no biggie. Go ahead and warm it up a bit so it flows better and sterile filter it. When you have all the solution in steril vial, then heat in oven at 250 if you like, its not necessary if you were sterile during making, but it cant hurt either. I did it with mine, cant be too carefull.