IGF injects - supposed to burn?

[Whacked]

Mine does.

Mine came with NACL and some sort of solution you put the IGF powder into.

Are there any brands of IGF that are painlesss -- perhaps using a different solution?

Also is anyone doing it subQ vs IM.

 

[drrman]

Mine does.

Mine came with NACL and some sort of solution you put the IGF powder into.

Are there any brands of IGF that are painlesss -- perhaps using a different solution?

Also is anyone doing it subQ vs IM.

well what i have found from experience is the acetic acid(solution you put into the IGF) is much stronger than what the sodium chloried(NACL) can actually neutralize......therefore its still acidid and burns like hell!

when i constitute it i usually use 1/2 ml of the AA and 1/2 ml of bacteriostatic water....instead of 1ml of the aa it comes with

 

[taoiron]

I like the sting!!

 

[plifter48]

Mine only stings for a few minutes. Nothing to worry about just the AA solution.

 

[Whacked]

cool---anybody else

 

[Big_Joe]

If it didn't sting you'd think it was just water.

 

[JohnnyWest]

You could always cut it with something else.

 

[perp69]

Not sure if you mentioned it or not but goin IM made all the difference in the world for me. Subq gave me welts and hurt like hell.

Perp

 

[Bourget]

Sorry for the stupid question but here goes.

I mixed my 1ml AG-Guys IGF-1 with 3ml water(BA). Now I wanna use 40mcg for each inject so what I did was figure that 1000mcg divided by 40mcg equals a total of 25 shot from this 1ml vial. I then added the 3ml of water I added and figured that 1.6mcg in a slin pin would yield 40mcg of IGF-1(4000mcg divided by 25 equals 1.60).

Once again, sorry for the question but I never really was any good at this stuff and I wanna make sure I dont fuck anything up.

Thanks
Bourget

BTW my inject burned too. Got a little nervous since I have never used IGF-1 before but I'm still alive so I guess it's all good.

 

[drrman]

Sorry for the stupid question but here goes.

I mixed my 1ml AG-Guys IGF-1 with 3ml water(BA). Now I wanna use 40mcg for each inject so what I did was figure that 1000mcg divided by 40mcg equals a total of 25 shot from this 1ml vial. I then added the 3ml of water I added and figured that 1.6mcg in a slin pin would yield 40mcg of IGF-1(4000mcg divided by 25 equals 1.60).

Once again, sorry for the question but I never really was any good at this stuff and I wanna make sure I dont fuck anything up.

Thanks
Bourget

BTW my inject burned too. Got a little nervous since I have never used IGF-1 before but I'm still alive so I guess it's all good.

if you mixed it with 3 more ml of water you now have 250mcg/ml of water bro.

so if you wanted to shoot 50mcg you would inject 20 units of the final solution you just made

don't know where you got 4000mcg/25=1.6

anyways, if you are wanting to use 40mcg per inject you will inject 16 iu's of the solution you have

 

[Bourget]

if you mixed it with 3 more ml of water you now have 250mcg/ml of water bro.

so if you wanted to shoot 50mcg you would inject 20 units of the final solution you just made

don't know where you got 4000mcg/25=1.6

anyways, if you are wanting to use 40mcg per inject you will inject 16 iu's of the solution you have

I don't understand. I started out with 1000mcg(1ml) IGF-1 and added 3ml(3000mcg) water.

I absolutely suck at this kind of math! Thanks for the response.

 

[Bourget]

Nevermind I just remembered that mcg is a measure of weight and ml is a measure of volume. I diluted my 1000mcg/ml making it 250mcg/ml of water. DUH!!

 

[drrman]

Nevermind I just remembered that mcg is a measure of weight and ml is a measure of volume. I diluted my 1000mcg/ml making it 250mcg/ml of water. DUH!!

thats it!

stuff can sometimes get confusing if you think about it too much!