how do you not waste your IGF?

[kevin6]

hi all!

it is very hard to draw up .03 ml of IGF which i bought at a concentration of 1mg/ml and want to run at 60 mcg/day for a month...and i think i'm losing IGF in the needle alone.

so....

can i draw up bacteriostatic water after drawing IGF in order to 'flush' the IGF out of the needle and into the syringe chamber? this would minimize IGF loss i think.

any thoughts much appreciated!

k

 

[southpaw45]

I would draw a little more than what you need. How much do you really think the needle itself actually holds.

 

[Indy]

hi all!

it is very hard to draw up .03 ml of IGF which i bought at a concentration of 1mg/ml and want to run at 60 mcg/day for a month...and i think i'm losing IGF in the needle alone.

so....

can i draw up bacteriostatic water after drawing IGF in order to 'flush' the IGF out of the needle and into the syringe chamber? this would minimize IGF loss i think.

any thoughts much appreciated!

k

that's what you should do, draw the igf, then pull plunger back abit until you get a little bubble, this will keep your ifg from going into the water bottle. then draw your water, stop and pull plunger back a little again creating a bubble there. rotate syringe around 5 or 6 times to use the bubble to mix the igf and water, burp the bubble and shoot.

indy

 

[moose11]

"burp the bubble" sooo cute ;-)

 

[basskiller]

do it in reverse.. draw the water first, then the igf.. that way your sure to get all of the igf

 

[Prizz]

So, if you have a 30IU Insulin syringe..... 30IU's of IGF-1 is actually 3IUS on the insulin syringe..... This is correct right?

rizz

 

[Indy]

do it in reverse.. draw the water first, then the igf.. that way your sure to get all of the igf

From Omega:

So how do you measure Omega's Igf. This is easy, but I see that it
is complicated for some, or better said. They make it harder than
what it really is. You always want to use a slin pin when using
LR3. I have seen post about there igf not lasting long enough. Why
I ask, what did you use to measure your igf out with.... There
response was.... a 3cc 1/2inch needle.. Well there's your
problem... So please never use something of the sort.... thats to
big of a bozuka to be trying to measure something out so fine. You
will want to stick with a 100 iu slin pin, or 50 iu slin pin, but
preferably 100iu pin. This allows you to work with more space when
drawing your water. Measuring igf on a 100 iu pin is simple. Each
(LITTLE) Black Click = 20mcgs, so 2clicks = 40, and 3clicks=60 and
so on... As for a 50 iu pin each click is 10mcgs. I belive you all
can do the math on that one. Once you have pulled out your desired
dose. You will want to use the bacteria static water to dilute the
igf . (YOU NEVER MIX THE WATER WITH THE VIAL OF IGF.... IF YOU DO,
YOU NEED TO CONTACT YOUR NEAREST IGF SUPPLIER FOR ANOTHER VIAL,
BECAUSE IT'S TOASTED) Here is the proper way to mix your water, and
igf. Once you have pulled your igf out, pull back just a little
click, this insures you that your not wasting any when inserting
the pin into the water. You then pull the water back to the (90iu
mark). So you have enough room to pull back again, which will
provide you a bubble. This bubble is your best friend .. It mixes
the igf, by you turning the slin pin up, and down approx. 5-6
times. You NEVER want to SHAKE this to mix the two. The igf is
fragile, and you will ruin the Lr3's life. Once you see the igf has
mixed with the water, push the air bubble out. It's just that
SIMPLE.

 

[basskiller]

From Omega:

So how do you measure Omega's Igf. This is easy, but I see that it
is complicated for some, or better said. They make it harder than
what it really is. You always want to use a slin pin when using
LR3. I have seen post about there igf not lasting long enough. Why
I ask, what did you use to measure your igf out with.... There
response was.... a 3cc 1/2inch needle.. Well there's your
problem... So please never use something of the sort.... thats to
big of a bozuka to be trying to measure something out so fine. You
will want to stick with a 100 iu slin pin, or 50 iu slin pin, but
preferably 100iu pin. This allows you to work with more space when
drawing your water. Measuring igf on a 100 iu pin is simple. Each
(LITTLE) Black Click = 20mcgs, so 2clicks = 40, and 3clicks=60 and
so on... As for a 50 iu pin each click is 10mcgs. I belive you all
can do the math on that one. Once you have pulled out your desired
dose. You will want to use the bacteria static water to dilute the
igf . (YOU NEVER MIX THE WATER WITH THE VIAL OF IGF.... IF YOU DO,
YOU NEED TO CONTACT YOUR NEAREST IGF SUPPLIER FOR ANOTHER VIAL,
BECAUSE IT'S TOASTED) Here is the proper way to mix your water, and
igf. Once you have pulled your igf out, pull back just a little
click, this insures you that your not wasting any when inserting
the pin into the water. You then pull the water back to the (90iu
mark). So you have enough room to pull back again, which will
provide you a bubble. This bubble is your best friend .. It mixes
the igf, by you turning the slin pin up, and down approx. 5-6
times. You NEVER want to SHAKE this to mix the two. The igf is
fragile, and you will ruin the Lr3's life. Once you see the igf has
mixed with the water, push the air bubble out. It's just that
SIMPLE.

I've never once had a problem.. even with his igf