Help with simple homebrewing questions...

[psychedout]

I am brewing up a prop/tren mix (both are powders) sometime in the near future.

The plan is to put 100mgProp and 100mgTren per cc. Is this reasonable? Seems reasonable to me. Is 5% BA enough to make this dissolve?? I know 5% is high enough to maintain a fairly sterile environment, but will it dissolve??

Thanks. Also I would like to here your personal homebrew experience.

 

[GoinDeep]

Need more info. What's the total your trying to make?

 

[psychedout]

How many mls? I am brewin 100mls. 50ml x 2 though.

 

[bicepts101]

I am brewing up a prop/tren mix (both are powders) sometime in the near future.

The plan is to put 100mgProp and 100mgTren per cc. Is this reasonable? Seems reasonable to me. Is 5% BA enough to make this dissolve?? I know 5% is high enough to maintain a fairly sterile environment, but will it dissolve??

Thanks. Also I would like to here your personal homebrew experience.

you've a pm

follow up on it. its a good place for quick Q's

karma is always welcome

 

[psychedout]

Also, please don't move this to the homebrew section. Everyone knows as well as I know that no one really goes there. Afterall, whens the last time youve been there?

 

[GoinDeep]

I'd say 10ml would be a good place to start. If you swirl it and find it hard to mix just ad a little more. I use 10ml BA and 5ml BB, mostly use the BB cause the recipe I had called for it originally and I still have it so I use it.

Some may say different, everyone has their own special way I suppose.

P.S. I could get away with 5ml w/just the tren but I use 10ml without pain. Just creates a little thinner mix after the oil is added.

 

[psychedout]

Thanks for the reply goingdeep.

Is BB really nesecary also? I have heard of people doing conversions with BA only.

 

[Andy13]

You are going to have add a lot of BA..

I say forget about it.. Make the solutions separate and inject twice as much.

 

[psychedout]

Hmmm. Andy, you would really need that much ba?

Like i've seen 200mg test E that has 2% ba, which is hardly any.

Its my understanding that short esters need more BA to dissolve, but is it really that much? How much BA are we talking about? Like how much would I need (hypothetically) to create this brew.

 

[Animal]

Te doesn't need that much or really any because it's a liquid at room temp.

BA DOES NOT make anything sterile! It impedes growth, but DOES NOT kill bacteria. If there is BA and bacteria in a solution and then in a depot, when the BA leaves the depot which is rather fast, the bacteria are free to grow and you have an abcess. If BA did anything like is claimed in the way of sterility there'd never be an abcess. The only way to sterilize is heat or sterile filter.

You will need a good bit of Ba, so much so that most people can't use it without pain. You will need 20-25% BA to start and it may still drop out within a few hours and require heating before each use.

 

[psychedout]

Alright. I think ive got this figured out.... Ill try for 150mg/ml total, or maybe just 100mg/ml total.

As for my next question.

What temperature is ideal for heating the gear at, and how long should I do it for?

 

[rjl296]

250 degrees, 1 hour

 

[psychedout]

Thanks. This may be a dumb question too, but I assuming that I do this in the open vial I am brewing in right?? Or can I do it in the vial I am planning on keeping it in -- would the rubber thing you stick your pin through melt?

 

[Animal]

The stoppers get soft at 300F or so, so you have some room before it's ruined.