Please Scroll Down to See Forums Below
napsgear
genezapharmateuticals
domestic-supply
puritysourcelabs
UGL OZ
UGFREAK
napsgeargenezapharmateuticals domestic-supplypuritysourcelabsUGL OZUGFREAK

Fina and glue???

68GT350

New member
I'm sorry if this sounds like a total newbie thread but I sorta am and I tried to research this to no avail.

I'm using sesame seed oil to inject Fina cuz I just got hit super hard with expenses. Now I know the kit is the way but it's takin some time and I gotta use my Fina NOW!!!

My question is, are these glues really harmful and do they even exists since I read that the pellets are just pressurized into their form.

Also, please tell me why use sesame seed oil over any other (i'm guessing consistency) oil and what is the proper proceedure, just to see if I've been screwing this up. Thanks
 
I just stopped using DMSO cuz everyone at work said I smelled like garlic, regardless of how much I used.

I ended up using half a teaspoon and I still stunk.
 
Are you planning on just grinding up the pellets and putting them into regular seasame seed oil? I hope not. That is very unsterile and you're begging for an infection. All the ingredients in finaplix are able to be injected IF sterile...
 
Yeah...I was microwaving and baking to sterilize. I'm ok so far!

What do you suggest with sesame seed oil? Can u suggest anything to dissolve the fina more? It's clumpy as hell.
 
Ok, I'm not gonna argue but I know people do it for an entire cycle and they do it painlessly. I just don't know what they do. Someone's gotta know.
 
One of my friends doesn't use the kits, even though I tell him too.... All he does is take a glass bowl, and just grind the shit out of the pellets until they are a very light powder, and dumps it directly into the oil..... He then does the oven sterilization.... 250 degrees for 15 minutes, let cool for 20 minutes, repeat 2 more times... He says it works, but I'm always skeptical... I prefer using the kits, knowing that I'm injecting a fully broken down injection instead possible particles....
 
I know this one guy who takes 20 pellets crushes them up and mixes them with 2cc's everclear he swirls this around at low heat in hot water, say 150! After dissolved he heats up some vegetable oil, which heats up real quick, he lets it cool some then mixes about 7 cc's with the everclear with hot water then he pulls 2cc's and injects. He says you must heat up and shake every inject and this evaps some of the everclear, should yield 4 shots at 2cc's 100mgs per shot the other cc is evap due to heating. He's pretty buff and hasn't had a problem yet! Remember the cranberry 2 pills 3x a day! Also milk thistle and all the basics!! he told me to tell you good luck!!:cool:
 
dissolving Fina

Fina dissolves in alcohol. Benzyl Alcohol is what is believed to be the "secret" ingredient in the kit.
Problem though is that if the mixture isnt the right proportions the shots are going to hurt or there wont be the right/desired amount of TBA per cc.
 
Re: dissolving Fina

marky said:
Fina dissolves in alcohol. Benzyl Alcohol is what is believed to be the "secret" ingredient in the kit.
not according to animal, he specifically says there is no benzyl alcohol in his kit at all..synthol's kit might have some
 
Damn...this is some good info I never thought of. Needle gets so damned clogged. It's gonna be a relief to see I got it sterlized. Thanks!

:)

Again, though, why is sesame seed oil constantly referred to and the friend of tricepula uses veggie oil with no problem. Is there something beneficial with sesame seed oil?
 
I believe that sesame seed oil is better for you than vegetable oil and it may be thinner too!!!:D
A 12cc or so bottle will suffice, probably have one in the cabinet, just resterilize real well, should be glass he says!
 
Tricepula,

Thanks a bunch and Thank your friend for me. I am extremely grateful...Now off to the liquor store!
 
Top Bottom