Crystallised Masteron... help!

[barrybounce]

Hi guys, i have two vials of drostanolone enanthate (Masto250) which have crashed. There are crystals at the bottom of the vial. It is 250mg/ml and i have no idea what to do with them. I have already heated these up in hot water and the crystals dissolved back into solution. However, when it cooled down, it crashed once again. Now ive been thinking of adding either some ba, some bb, some eo or simply more oil. But i have no idea what to do. I was going to add some ba and bb but a mod from another board suggested eo. Now i'm thinking if i add ba or bb or eo, will i need to filter the solution??? The 2 vials are UG labs and i have never homebrewed before so it would be a new experience for me. Another solution i thought of was to buy some filtered oil and then just add that and reheat. Would that work? Can i mix oils in solution as i have no idea what oil has been used. Any advice would be appreciated. Thanx.

 

[79steeler]

Hi guys, i have two vials of drostanolone enanthate (Masto250) which have crashed. There are crystals at the bottom of the vial. It is 250mg/ml and i have no idea what to do with them. I have already heated these up in hot water and the crystals dissolved back into solution. However, when it cooled down, it crashed once again. Now ive been thinking of adding either some ba, some bb, some eo or simply more oil. But i have no idea what to do. I was going to add some ba and bb but a mod from another board suggested eo. Now i'm thinking if i add ba or bb or eo, will i need to filter the solution??? The 2 vials are UG labs and i have never homebrewed before so it would be a new experience for me. Another solution i thought of was to buy some filtered oil and then just add that and reheat. Would that work? Can i mix oils in solution as i have no idea what oil has been used. Any advice would be appreciated. Thanx.

Bro I would get with whomever you need to and get them replaced. you should not have to bake, or boil or do anything to that gear, it should have been right the first time.

Stop excepting sub par gear bro's.

 

[barrybounce]

Normally i would send it back but i bought this stuff ages ago... im talking maybe a year and ive already put it in hot water so the vial looks like its been played with. So if i cant sort this out i will have to bin it. But no point throwing it away since i hear it is quite common. I just need a way to fix this problem that will keep it sterile. Thanx

 

[79steeler]

Place it on a cookie sheet and place a needle in the stopper, but not so deep it touches the oil. Preheat your oven to 250 degrees and put the gear in the oven for 20 minutes. Take it out and let it cool naturally, remove the needles. The needle is just to relieve any air pressure which may occur. Good luck.

 

[barrybounce]

will try that but isnt that the same as when i put it into hot water on the stove? I put water into a pan about 3/4 up the vial and brought the water to the boil. When the water was boiling, i reduced the heat to simmering and put the vial in. It took almost an hour but the crystals dissolved back into solution. But these were back a few days later. So just wondering if that would bring about the same outcome??

 

[Domimar]

I usually get a 1quart pot fill it up with water almost as high as the fluid in ur gear bottle, then put the burner on med to med high, and wait till u see the crystals dissappear. That should last a couple days, then have to the process over, every couple days. The gear is still good, just whoever made it didnt put in enough bb or ba.

 

[barrybounce]

Thats what i thought and i was thinking of getting some sort of solvent and adding it instead of heating it up every few days. But the dilema i have is which solvent, how much and whether adding some usp ba/bb or NF ethyl oleate would now mean that the solution would need to be filtered. If not then i could just add a ml of eo or whatever to each vial and reheat. Thats what i want to know. Thanx guys

 

[cboogsrun]

Try adding 2% BA If its 10cc's then add .2 cc's of BA. Heat and let cool If it crashes again add another 2% ect... Generally this is the cause of crashed gear that I have run into. I recently had to add 6% to some tren, which makes my buttcheeks kinda scared lol