Trying to make Tren E over 200mg/ml???

[mohsan]

I am trying to make a solution of 200mg/ml of Tren Enanthate. I have the following supplies:

5g tren
USP grade grapeseed oil
BA
BB
Syringes and needles
Sterile Vials
Whatman Filters

I've pasted the recipe I'm referred to below.

My question is if I wanted to make 200mg/ml concentration, can I use the same amount of BA as the 100g/ml recipe says. Would I also have to add BB since the concentration is higher? If so, how much?

Stupid question, but do BB and Oil mix well---or will it become a suspension after sitting there for a while?

Basically, I'd be following the same recipe pasted below except using 10g of Tren E powder rather than 5g. (I do realize, the concentration will become sllghtly lower than 200mg/ml). Will this work?

Thanks in advance.


----BEGIN PASTE----
Tren

Note: this conversion is not for the pellet form

Powder: 5 grams
Produces: 50 ml @ 100 mg/ml

Requirements:

* 5 grams tren
* 43.75 ml sesame oil
* Benzyl Alcohol 2.5 ml 5% BA
* Syringes 3cc & 5/10cc
* 18 or 20 gauge needles
* Vial
* Sterile Vial
* Whatman sterile filter


Procedure:

* measure 5 grams of powder
* place the powder in the vial
* add BA to the vial
* heat the oil in a suitable container in the oven to a minimum of 212 degrees F to sterilise it (it will likely be necessary to use slightly more oil than listed as you will not be able to utilise all of it)
* add the oil to the vial but save 2 ml of oil in the syringe for later
* gently shake the vial.
* reheat the mixture if necessary by placing the vial in a frying pan and place it on the eye of the stove
* place an 18 or 20 gauge needle in the sterile vial and attach the Whatman sterile filter
* place another needle in the sterile vial to relieve the pressure
* draw out the solution with a syringe and run it though the Whatman filter
* take the other syringe with 2 ml of oil (saved previously) and run it through the Whatman filter into the solution.

 

[mohsan]

Errr. rather I have 10g of Tren Enanthate powder instead of 5.

I am trying to make a solution of 200mg/ml of Tren Enanthate. I have the following supplies:

5g tren
USP grade grapeseed oil
BA
BB
Syringes and needles
Sterile Vials
Whatman Filters

I've pasted the recipe I'm referred to below.

My question is if I wanted to make 200mg/ml concentration, can I use the same amount of BA as the 100g/ml recipe says. Would I also have to add BB since the concentration is higher? If so, how much?

Stupid question, but do BB and Oil mix well---or will it become a suspension after sitting there for a while?

Basically, I'd be following the same recipe pasted below except using 10g of Tren E powder rather than 5g. (I do realize, the concentration will become sllghtly lower than 200mg/ml). Will this work?

Thanks in advance.


----BEGIN PASTE----
Tren

Note: this conversion is not for the pellet form

Powder: 5 grams
Produces: 50 ml @ 100 mg/ml

Requirements:

* 5 grams tren
* 43.75 ml sesame oil
* Benzyl Alcohol 2.5 ml 5% BA
* Syringes 3cc & 5/10cc
* 18 or 20 gauge needles
* Vial
* Sterile Vial
* Whatman sterile filter


Procedure:

* measure 5 grams of powder
* place the powder in the vial
* add BA to the vial
* heat the oil in a suitable container in the oven to a minimum of 212 degrees F to sterilise it (it will likely be necessary to use slightly more oil than listed as you will not be able to utilise all of it)
* add the oil to the vial but save 2 ml of oil in the syringe for later
* gently shake the vial.
* reheat the mixture if necessary by placing the vial in a frying pan and place it on the eye of the stove
* place an 18 or 20 gauge needle in the sterile vial and attach the Whatman sterile filter
* place another needle in the sterile vial to relieve the pressure
* draw out the solution with a syringe and run it though the Whatman filter
* take the other syringe with 2 ml of oil (saved previously) and run it through the Whatman filter into the solution.

 

[fcfmuaythai]

i use 2%BA/15%BB, that holds it up to 300mg/ml.

 

[mohsan]

If I don't use any BB, can I get that high of a concentration. My question is the BB here for dissolving purposes?

i use 2%BA/15%BB, that holds it up to 300mg/ml.

 

[fcfmuaythai]

the BB is used to thin out the solution as well as a secondary solvent. If you want really high concentration tren, substitute half of the oil called for in the recipe with ethyl oleate.

 

[nreviya]

I made Tren E 250/ml using 5%BA and 15%BB. It hurts big time. It is even swollen. Tried to bake it on 250 F for 45 min. Did not help Any ideas????

 

[interleukin 1]

I made Tren E 250/ml using 5%BA and 15%BB. It hurts big time. It is even swollen. Tried to bake it on 250 F for 45 min. Did not help Any ideas????

That is a high amount of benzyl alcohol...I am sure that is what is killing you. Try to pull out 1 or 2 mls (or what ever amount you are going to use at that specific time) and place the drug onto a sterile spoon...then slowly flame the spoon over a flame and get the BA to "flash off".. Meaning the BA is a very low flash point. So pull it out as soon as this reaction takes place. The BA will burn off rather quickly and the flame will go out in a matter of a few seconds. Then go ahead and inject the "BenzylA-less" test. You want to do this ASAP because you now have the agent exposed to a non-sterile enviornment (the air over your oven)....and there is nothing to keep the test from being contaminated...That is why you only do this as needed and not the entire vial. Hope you paid attention to aspetic technique in microbiology 101!

 

[DBBT]

3:17
3:18
3:20
2:20

depending on which compound it can change slightly as seen^^^^

 

[abmmij]

Get some Ethyl Oleate, will solv nicely and will be a painless product

 

[engdoug]

the BB is used to thin out the solution as well as a secondary solvent. If you want really high concentration tren, substitute half of the oil called for in the recipe with ethyl oleate.

Sorry to revive this old post, but, anyone can explain excatly what is the BB and BA ? What is the entire name of this, and where can I buy ?

Best Regards