whats the proper procdure when using amps

[wellbilt]

whats up guys iam looking for the proper procedures of injecting when using amps (or your procedure)now i know how to open them but iam not sure of the whole injecting procedure do you change the pin after pulling the gear out then clean the injection site then inject or do you clean the site open amp pull out gear and inject with the same pin any advice will be greatly appreciated iam looking to start my first inject cycle with omnas and iam really didnt find any info on this just want to make sure i do everything righ.thanks in advance for any replies

 

[instant.muscle]

i crack open my amp stick needle in bottom corner, suck in juice while rotating the amp til i get every last drop, clean injection spot w/ alcohol and inject w/ same needle.

 

[wellbilt]

thanks bro,so do you put the cover back on over the neddle while you clean your injection spot i know these questions ound stupid and basic but i think there is a great potentioal to fuck this up just making sure i covered all ground before i inject

 

[DiamondCutCows]

thanks bro,so do you put the cover back on over the neddle while you clean your injection spot i know these questions ound stupid and basic but i think there is a great potentioal to fuck this up just making sure i covered all ground before i inject

YES, always better to be TOO sterile as opposed to not!

 

[LVTitan]

thanks bro,so do you put the cover back on over the neddle while you clean your injection spot i know these questions ound stupid and basic but i think there is a great potentioal to fuck this up just making sure i covered all ground before i inject

i do put the cover back on while i reswab. i crack openthe amp, pull all the gear out, but i have noticed that the needle even barely touches the amp, it dulls it and makes injecting harder, so i change the needles, makes a huge difference. hope that helps

 

[wellbilt]

thanks lv and diamond much appreciated

 

[growthspurt]

thanks lv and diamond much appreciated

Hey Bro-

If you really want to be thorough, swab the amp with an alcohol pad, then crack it open. Next use an 18g filter needle at the end of the syringe. I knew someone who worked @ a hospital who got em for me. The filter needle looks like a normal needle but it has a small micro filter at the top of it. They use these specifically for injections from amps at the hospitals. You'd be surprised at the amount of small glass particals that could possibly contaminate your gear and make their way into your ass cheek. After you use the filter needle, switch to your favorite pin and you're good to go! Hope this helps.

 

[bicepts101]

i always change the needle no matter what....better safe than sorry

 

[wellbilt]

i always change the needle no matter what....better safe than sorry

thanks bro.i this is wat i plan to do i order lots of pins and there cheap better safe then sorry

 

[wellbilt]

things go bump in the night.

 

[manny78]

open the amp, clean the site, inject, clean again, get rid of the syringe/needle.

Syringes are dirt cheap here so I just get a new one for each injection.

 

[wellbilt]

so you go stright from the amp to the injection spot manny

 

[manny78]

so you go stright from the amp to the injection spot manny

Yes. I use human grade so there's no reason to bake it or do any other weirdo trick.

 

[wellbilt]

iam will be using human grade gear to ,so does anyone use filtered needles when using amps i have heard of the being recomended when using amps due to small pieces of glass

 

[instant.muscle]

most people change needle so it isnt dull. the pain dosnt bother me as long as its clean. since i was first 2 reply, karma 2 me

 

[wellbilt]

i gotta spread it around bro before i hit ya gain i will though i promise thanks again

 

[bw1]

I always change pins, 18 to draw... 23 or 25 to inject depending on where. Pins are cheap

 

[terrapin]

whats up guys iam looking for the proper procedures of injecting when using amps (or your procedure)now i know how to open them but iam not sure of the whole injecting procedure do you change the pin after pulling the gear out then clean the injection site then inject or do you clean the site open amp pull out gear and inject with the same pin any advice will be greatly appreciated iam looking to start my first inject cycle with omnas and iam really didnt find any info on this just want to make sure i do everything righ.thanks in advance for any replies

Cracking them open and pulling the gear out with a syringe?? I thought they were suppositories!!!!!

 

[BIGJAKE]

I always change pins, 18 to draw... 23 or 25 to inject depending on where. Pins are cheap

ALWAYS CHANGE THAT PIN AFTER YOU DRAW IT OUT.i use 22g 1 1/2" to pull
it out then just lift up side down put the plunger back switch pins clean site and you know the rest.

 

[instant.muscle]

why always switch?

 

[wellbilt]

thanks for the replies guys