Test Prop above 100mg/ml

[anal itch]

Has anyone made Test Prop above 100mg/ml? I'm thinking about making 150mg/ml but was wondering if I would have to increase the percentage of BA/BB. I was going to use 5% BA and 15% BB per the instructions in the powder conversion thread but will add more powder. Will it stay in solution at 150mg/ml with a 5/15 ratio?

 

[Ofcfriendly]

Think it will hold. Prop gets to be a pain in the ass (both figuratively and literally) at higher concentrations, though.

 

[25homes]

Will hold but is going to hurt like a mofo.....would drop the ba back to 3%

 

[anal itch]

Will hold but is going to hurt like a mofo.....would drop the ba back to 3%

cool, I plan on making a small batch to test the waters so to speak. I can tolerate porp pain rather well so I figure it should be fine. Will post results soon.

 

[scoobysgym]

Youll be fine I would however go 5 and 15 and heat up the mix in a bath after you add the ba and bb before adding oil doing it this way i HAVE NEVER HAD A PROB. Dont know if you have seen this or not but its a cool tool for the toolbox http://absinth.greatnow.com/calcpowder2.html Laters - scooby

 

[anal itch]

That calculator rocks! Save the source code and save it has an HTM. You never know when a site can go down or away. I also saved Kain's conversion instructions in a word doc.

 

[boskers22]

wat if EO was used would 150mg/ml be a problem, if not wat about 200mg/ml?

 

[boskers22]

bump

 

[Ofcfriendly]

wat if EO was used would 150mg/ml be a problem, if not wat about 200mg/ml?

I've been hearing on the boards that prop is a little tricky to get to hold at 200mg/ml in EO. A UG is claiming that they've gotten it to hold and are about to market it. I'm jumping on this one because its said to be painless.

 

[Para_Shoot]

I made test prop at 200mg/ml using a 3/13 mix. I use this for everything else, even cyp at 250mg/ml and everything works perfect...Except the prop. After about 16 hours it started to crystalize bad. I then added the difference of BB to bring it up to a 3/18 mix and slowly heated it till it was a pure honey liquid, all crystals gone. That did not do it, as it started to crystlize again. Then I added the difference of BA to get to a 5/18 mix and it is holding perfect, no crystals. I really didn't want to go to 5%BA, but it is working now. Haven't shot it yet so don't know the pain factor, if there even is one. I'll post my pain report after tommorow morning when I sink that prop in me.

 

[anal itch]

I made test prop at 200mg/ml using a 3/13 mix. I use this for everything else, even cyp at 250mg/ml and everything works perfect...Except the prop. After about 16 hours it started to crystalize bad. I then added the difference of BB to bring it up to a 3/18 mix and slowly heated it till it was a pure honey liquid, all crystals gone. That did not do it, as it started to crystlize again. Then I added the difference of BA to get to a 5/18 mix and it is holding perfect, no crystals. I really didn't want to go to 5%BA, but it is working now. Haven't shot it yet so don't know the pain factor, if there even is one. I'll post my pain report after tommorow morning when I sink that prop in me.

Thanks for the info! Keep us posted!

 

[Para_Shoot]

Thanks for the info! Keep us posted!

Ok, I injected it last nite about 9pm EST. Now it is 6:45am EST and NO prop burn. I am convinced that now I can make painless 200mg/ml prop at 5%BA and 18%BB, so it won't crystalize. Anyone else have crystal problems with prop 200 or above? If 5%BA didn't burn me, and I have taken doctor prescribed prop that did burn, I wonder how much BA was in the doctor prescribed prop.

 

[drrman]

Ok, I injected it last nite about 9pm EST. Now it is 6:45am EST and NO prop burn. I am convinced that now I can make painless 200mg/ml prop at 5%BA and 18%BB, so it won't crystalize. Anyone else have crystal problems with prop 200 or above? If 5%BA didn't burn me, and I have taken doctor prescribed prop that did burn, I wonder how much BA was in the doctor prescribed prop.

good info!