Test cyp crystalize?

[BC975]

What is the best way to get my test-cyp back to normal? I've heard of boiling it in water for five min, putting it in the oven for 5 min at 200 degressF. Looking to see what yall think is the best way.

 

[maldorf]

What is the best way to get my test-cyp back to normal? I've heard of boiling it in water for five min, putting it in the oven for 5 min at 200 degressF. Looking to see what yall think is the best way.

Is this a home brew? Never had that happen to me with stuff I bought. Heating is in a pan of hot water on the stove top will get it back into solution, but it might just crash again once it cools down and sits long enough. If the mixture isnt quite right, you might have to add some more BA to get it to go back into solution.

 

[Jon79]

if it is not homebrew tell your source and he should send you another one..

that's the best thing to do

 

[BigAndy69]

if it is not homebrew tell your source and he should send you another one..

that's the best thing to do

That's a good option

Try heating it in a pan as suggested. Cyp falls out of solution quite easily (even pharmacy cyp can form crystals) It should get back into solution quickly....If it doesn't it's a write off.

 

[BC975]

not a homebrew...talked to my source and he told me about the pan idea. It is pharmacy cyp btw. Source said that it could have gotten too cold...thanks

 

[BigAndy69]

not a homebrew...talked to my source and he told me about the pan idea. It is pharmacy cyp btw. Source said that it could have gotten too cold...thanks

In that case it will be fine, just heat it up.

 

[maldorf]

not a homebrew...talked to my source and he told me about the pan idea. It is pharmacy cyp btw. Source said that it could have gotten too cold...thanks

Yeah, it should go back into solution. If this doesnt work, a very small addition of BA will help bring it into solution. I wouldnt add more than 1% BA though, too painful of an injection possibly.

 

[Big O]

let me guess...ip....

 

[Mr.X]

What is the best way to get my test-cyp back to normal? I've heard of boiling it in water for five min, putting it in the oven for 5 min at 200 degressF. Looking to see what yall think is the best way.

Bake it, and maybe find another source.

The easiest way is to bake the gear:

Put a pin in the top (just pin , NOT syringe)
pre-heat oven to 175 F^o
bake for 10 min
let cool for 30min
(repeat 2-3 times).

PLEASE USE A GLOVE FOR YOUR OWN GOOD

 

[boxerjake]

The olny time i've seen cyp do that is when trying to high of a concentration per ML

I'd try the re-heat - " but " afterwards let it stand for better then a week . If it forms crystals again then i'd pitch it fast ......

Test hormones disolve fairly easy into oil , right up untill it reachs the saturation point

 

[Big O]

wait till you inject it.....i bought some test cyp from ip....i threw the shit away...it was over 300 mg's....painfull shit...good luck with that

 

[BC975]

I injected two days ago...my ass is still in a lot of pain. I have test cyp 250...two vials actually and they both have seem to crystalize. Mr X..when you say put a pin through the top is that in the solution or just inside (meaning in air not liquid). I called another source in my area but he recently got a package of bs deca so that source is out. Thanks for all the imput.

 

[maldorf]

I injected two days ago...my ass is still in a lot of pain. I have test cyp 250...two vials actually and they both have seem to crystalize. Mr X..when you say put a pin through the top is that in the solution or just inside (meaning in air not liquid). I called another source in my area but he recently got a package of bs deca so that source is out. Thanks for all the imput.

Dont let the needle enter the fluid, just have it in air. This is done to equalized the pressure inside the vial to the outside air pressure. Pressure increases as temperature does you know, so if you dont vent it the top will blow off or worse!