Please Scroll Down to See Forums Below
napsgear
genezapharmateuticals
domestic-supply
puritysourcelabs
UGL OZ
UGFREAK
napsgeargenezapharmateuticals domestic-supplypuritysourcelabsUGL OZUGFREAK

QVE-004 Enth 50ml -- Pain reduction by leaps and bounds...

  • Thread starter Thread starter Citruscide
  • Start date Start date
C

Citruscide

Guest
Ok... here's an Abstract.

A "friend" of mine *wink* tried this, and it worked wonders for him *wink*

I know that you cannot boil off the BA (398F boiling point) and hormones break down at 400-450 ... too close for comfort... but this tactic has seemed to work for a couple bros.

Heat your oven to 250F, and cook your bottle (making SURE to put a dart, minus the syringe, in the top... so that air can escape... make sure hte dart is not in the liquid, as some might ooze out that way). Heat it for 3 sessions of 25 minutes at 250F, letting it cool for 15 minutes in between heatings.

The injections that result afterward have been reported as follows.

1cc injection into shoulder... felt like standard test shot... even like QV Prop... no swelling, no serious pain.

2cc injection into glute ... did cause a small lump to appear, but ZERO pain, no "test flu" symptoms that were experienced before baking at 250F.

2cc injection into quad .. same as glute, minues the smaller lump

Hope this can help some bros

C-ditty
 
Well... either way. Take it for what it is worth.

The pain was drastically reduced after the baking. There were feelings of "feverish" symptoms prior to baking. Don't know if "flu-like" is the correct term... but feverish.

I woudlnt' think it would help any, but it did. :)

c-ditty
 
True... but if one has no EQ or no DECA... and is on a test only cycle... this seems to help...

Unless you have some EQ to send to someone... :)

C-ditty
 
Another technique I think Billy B over at Steroidology uses:
since BA is water soluble, squirt some bacteriostatic water into the vial of test. Shake it up good a few times, then let sit until the water partitions out on top of the oil. Suck out the water, which should contain some of your excess BA. Voila! Less pain, fever, flu (we hope).
 
buffdoc said:
Another technique I think Billy B over at Steroidology uses:
since BA is water soluble, squirt some bacteriostatic water into the vial of test. Shake it up good a few times, then let sit until the water partitions out on top of the oil. Suck out the water, which should contain some of your excess BA. Voila! Less pain, fever, flu (we hope).
Click to expand...

Bad technique. And Fonz, Dancer, Macro, Ulter and rugger can tell you why. There is something about removing the BA that you do NOT want to do.

Mixing with another compound will not minimize the pain, it will only disperse a large amount of substance into the depot site and thus keep it from centering in one tight specific place.
 
bigdelt69 said:
I dont think that could have any effect on the 'test flu'.
Click to expand...

bigd, The "flu" is not caused by the test, it's the BA. Hence we don't get the flu from all types of test. I know a guy*wink*who used 40ml of cypionate over two cycles and never had any "flu" symptoms. Then when he tried QV enanth 50ml for the first time he was sick after every shot and hurting like hell for 2-3 days after each shot.

C, good method Bro'. It's the same thing one would do to disipate the BA after making fina. BAking x3 at 250 for 10 min. BTH like the *wink* thing, made me laugh!

B
 
AAP said:


Bad technique. And Fonz, Dancer, Macro, Ulter and rugger can tell you why. There is something about removing the BA that you do NOT want to do.

Mixing with another compound will not minimize the pain, it will only disperse a large amount of substance into the depot site and thus keep it from centering in one tight specific place.
Click to expand...



I'd like to hear why.
If you're saying it'll "crash" in the muscle, add some benzyl benzoate. This is lipid soluble. Or, you can add more sterile oil to dilute. Or both.
 
You must log in or register to reply here.
Top Bottom